HP 8753D - Page 521

N
NN
NN
NN
NN
NN
NN
N
S11A
is used
to enter
the standard
numbers for
the rst
class
required for
an S
11
1-port calibration.
(For
default cal
kits,
this
is the
open.)
N
N
N
NN
NN
NN
NN
NN
N
S11B
is used
to enter
the standard
numbers
for
the
second
class
required for
an S
11
1-port calibration.
(For
default cal
kits
,
this
is the
short.)
N
N
N
N
N
NN
NN
NN
NN
N
S11C
is used
to enter
the
standard
numbers
for
the
third
class
required
for
an
S
11
1-port
calibration.
(F
or
default
kits
,
this
is
the
load.)
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
N
N
N
N
N
N
N
N
N
N
S11
REFL SHORT
measures
the
short
circuit
TRL/LRM
calibration
data
for
PORT 1.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
NN
NN
N
N
N
N
N
N
S22
1-PORT
provides
a
measurement
calibration
for
reection-only
measurements
of
one-port
devices
or
properly
terminated
two-port
devices
,
at
port
2
of
an
S-parameter
test
set
or
the
test
port
of
a
transmission/reection
test
set.
N
N
N
N
N
N
N
N
N
N
N
N
N
N
S22A
is
used
to
enter
the
standard
numbers
for
the
rst
class
required
for
an
S
22
1-port
calibration.
(F
or
default
cal
kits
,
this
is
the
open.)
N
N
N
N
N
N
N
N
N
N
NN
NN
S22B
is
used
to
enter
the
standard
numbers
for
the
second
class
required
for
an
S
22
1-port
calibration.
(F
or
default
cal
kits
,
this
is
the
short.)
N
N
N
N
NN
NN
N
N
N
N
N
N
S22C
is
used
to
enter
the
standard
numbers
for
the
third
class
required
for
an
S
22
1-port
calibration.
(F
or
default
kits
,
this
is
the
load.)
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
N
N
N
N
N
N
N
N
N
N
S22
REFL
SHORT
measures
the
short
circuit
TRL/LRM
calibration
data
for
PORT
2.
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
SAMPLR
COR
on
OFF
selects
whether
sampler
correction is
on or
o.
N
NN
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
N
NN
NN
N
N
N
N
N
N
N
SAVE
COLORS
saves
the
modied
version
of
the
color
set.
4
SA
VE/RECALL
5
provides
access
to
all the
menus used
for saving
and
recalling
instrument
states
in
internal
memory and
for storing
to,
or
loading from,
external disk.
This
includes
the
menus
used
to
dene titles
for internal
registers
and
external
disk
les
,
to
dene the
content of
disk les
,
to
initialize
disks
for
storage
,
and
to
clear
data
from
the
registers or
purge
les
from
disk.
N
NNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNNN
NNNN
SAVE USER KIT
stores the user-modied or user-dened kit into memory
, after
it has been modied.
N
NNNNNNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNN
SAVE USING ASCII
selects ASCII format for data storage to disk.
NNNNNNNNNNNNNNNNN
NNNNNNNNNNNNNNNNNNNNNNNNN
NNNNNNNNNNN
SAVE USING BINARY
selects binary
format for data storage
.
NNNNNNNNNNNNNNNNNN
NNNNNNNNNNN
SCALE/DIV
changes the
response value scale per division of the displayed
trace.In
polar and Smith chart formats
, this refers to the full
scale value at the outer circumference, and is identical to
reference value.
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
SCALE PLOT [ ] toggles between two selections for plot scale, FULL and GRAT.
N
NNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNNN
SCALE PLOT [FULL]
is the normal scale selection for plotting on blank paper.It
includes space for all display annotations such as marker
values, stimulus values, etc. The entire display ts within the
Key Denitions 9-35