Need help?Do you have a question about the HP JH296A and is the answer not in the manual?
General| Product Type | Network Router |
|---|---|
| Product Series | HP 2920 |
| Model Number | JH296A |
| Layer | Layer 3 |
| Power over Ethernet (PoE) | No |
| Rack Mountable | Yes |
| Humidity | 10% to 90% non-condensing |
| Weight | 4.5 lbs |
| Memory and Processor | 512 MB Flash |
| Input voltage | 100 to 240 VAC |
| Power Consumption Description | 30 W (maximum) |
| Operating Temperature | 0°C to 45°C |
| Storage Temperature | -40°C to 70°C |
Introduces IGMP snooping as a mechanism to improve multicast forwarding efficiency on Layer 2 devices.
Explains the operation of IGMP snooping based on different IGMP message types.
Provides a checklist of tasks for configuring IGMP snooping.
Guides through enabling IGMP snooping globally and for specific VLANs.
Covers configuration of static ports, dynamic ports, and special port behaviors.
Describes how to enable and configure the IGMP snooping querier.
Details how to adjust query and response parameters for IGMP messages.
Covers configuring multicast group policies and source port filtering.
Offers examples for group policy, simulated joining, static ports, and querier configuration.
Addresses common problems with IGMP snooping, such as Layer 2 forwarding failure.
Guides on enabling IP multicast routing for public networks or VPN instances.
Covers configuring unicast routing protocols and enabling PIM.
Details how to configure static multicast routes, including RPF interface/neighbor.
Addresses common problems with multicast routing and forwarding.
Explains IGMP SSM mapping for providing SSM support to IGMPv1/v2 hosts.
Describes configuring IGMP proxying on edge devices to act as proxy or querier.
Provides a checklist of tasks for configuring IGMP features.
Guides through enabling IGMP, specifying version, and configuring static members.
Covers configuring IGMP query, response parameters, and fast-leave processing.
Details how to configure IGMP SSM mappings for SSM services.
Explains how to configure IGMP proxying on receiver-side interfaces.
Offers examples for basic IGMP features, SSM mapping, and proxy configuration.
Addresses common IGMP problems like no membership information or inconsistent membership.
Introduces PIM-SM's pull mode for sparse networks and the role of RPs.
Details RP discovery mechanisms, including static RPs and candidate RPs.
Explains Anycast RP for redundancy and optimal RP path selection.
Introduces PIM-SSM as a solution for source-specific multicast.
Section dedicated to configuring PIM-DM.
Provides a checklist of tasks for configuring PIM-DM.
Guides on enabling IP multicast routing and PIM-DM on interfaces.
Section dedicated to configuring PIM-SM.
Provides a checklist of tasks for configuring PIM-SM.
Guides on enabling IP multicast routing and PIM-SM on interfaces.
Covers configuring static RP, C-RP, and Anycast RP.
Guides on configuring Anycast RP for redundancy and optimal RP path.
Section dedicated to configuring BIDIR-PIM.
Provides a checklist of tasks for configuring BIDIR-PIM.
Guides on enabling PIM-SM before enabling BIDIR-PIM.
Covers configuring static RP, C-RP for BIDIR-PIM.
Details configuring static RPs for BIDIR-PIM.
Explains configuring C-RPs for BIDIR-PIM and RP-set information.
Details configuring a BSR for dynamic RP selection in BIDIR-PIM.
Explains C-BSR election and BSR policy configuration for BIDIR-PIM.
Section dedicated to configuring IPv6 PIM-SSM.
Provides a checklist of tasks for configuring IPv6 PIM-SM.
Guides on enabling IPv6 multicast routing and IPv6 PIM-SM.
Details configuring the IPv6 SSM group range for PIM-SSM.
Includes examples for configuring IPv6 PIM-DM, PIM-SM, and admin-scoped zones.
Explains implementing Anycast RP using MSDP peering relationships.
Provides a checklist of tasks for configuring MSDP features.
Guides through enabling MSDP and configuring peers.
Details enabling IP multicast routing and MSDP.
Explains how to specify an MSDP peer connection.
Covers configuring MSDP peering connections and related prerequisites.
Covers configuring SA message encapsulation, originating RP, and request messages.
Provides examples for configuring MSDP on routers.
Details configuring MSDP for inter-domain multicast in PIM-SM.
Addresses common MSDP problems like peers in disabled state or missing SA entries.
Guides on creating VPN instances and enabling IP multicast routing.
Addresses common MD VPN problems like default-MDT establishment failure.
Troubleshoots issues with default-MDT establishment and PIM neighbor relationships.
Guides through enabling MLD snooping globally and for specific VLANs.
Describes how to enable and configure the MLD snooping querier.
Addresses common MLD snooping problems like Layer 2 forwarding failure.
Troubleshoots issues where Layer 2 multicast forwarding fails.
Troubleshoots issues with IPv6 multicast group policy enforcement.
Explains the Reverse Path Forwarding (RPF) check for IPv6 multicast.
Addresses common IPv6 PIM problems like multicast distribution tree issues.
Troubleshoots issues with building IPv6 multicast distribution trees.
Troubleshoots issues where IPv6 multicast data is abnormally terminated.
To Next Page
