Husqvarna CTH126 - Symbols and Controls; Control Symbols Identification; Indicator Symbols Identification; Safety Symbols Identification

15
KEY PART
NO. NO. DESCRIPTION
KEY PART
NO. NO. DESCRIPTION
NOTE: All component dimensions given in U.S. inches
1 inch = 25.4 mm
1 532 44 20-48 Deck Weldment 30"Srd
2 532 19 51-61 Stud Fastner W/'D'anti-Rotation
3 873 90 05-00 Nut Lock Hex Flange 5/16 - 18
4 532 41 76-45 Bracket Clutch Cable
5 817 00 05-10 Bolt 5/16-18
6 532 41 88-63 Arm Susp Mower Rear Srd
8 532 42 02-52 Arm Idler 30"Srd
9 532 19 90-92 Spacer Retainer
10 817 00 06-16 Screw 3/8 - 16 x 1 Smgml Tap/R Blk
11 532 13 77-29 Screw Thd Roll 1/4 - 20 x 5/8
13 872 11 06-12 Bolt Carr Sh 3/8 - 16 x 1 - 1/2 Gr. 5
14 532 15 60-85 Keeper Belt Idler
15 532 14 67-63 Pulley Idler V-Groove Dim 4.25
16 873 90 06-00 Nut Lock FlG 3/8 - 16 unc
17 532 40 02-34 Nut Flange Lock Top
18 532 18 76-90 Washer Spacer Mandrel
19 532 11 04-85 Bearing Ball Mandrel
20 532 17 39-84 Screw Thd Roll Dod Pt Hex
22 532 17 58-20 Pulley Idler Flat
23 817 49 06-28 Screw Thdrol 3/8 - 16 x 1-3/4
24 819 13 20-12 Washer 13/32 x 1 - 1/4 x 12 Ga
25 532 42 02-53 Keeper Belt 30"Srd
26 532 42 02-55 Cover Mandrel Mwr 30"Black
27 532 41 92-71 V-Belt Drive
TRACTOR - - MODEL NO. CTH126 (96051000803), PRODUCT NO. 960 51 00-08
MOWER DECK
44
44
29 532 42 08-95 Hinge Pin
32 532 19 72-51 Spring Mower Drive
33 532 18 72-81 Housing Mandrel 4pt Service
34 532 19 28-72 Shaft Asm Mndrl N/Greaseable 38
35 532 41 92-74 Blade
36 532 19 30-03 Bolt/Washer Asm 7/16 - 20 unf
38 532 19 65-39 Bolt Shoulder
42 817 00 06-12 Screw Hexwsh THDR 3/8-16 x 3/4 BL
43 532 41 68-77 Pulley Mandrel 6 5 Pd 30"
72 532 41 72-36 Chute Upper SRD 30R
73 532 42 52-74 Chute Lower SRD 30R
74 532 12 46-70 Retainer Spring
76 532 41 55-98 Washout Port
80 532 42 30-62 Palnut 1/4
- - 532 19 28-70 Mandrel Assembly (Includes
Housing (key#33), Shaft Assembly
(key#34), and Bearing (key#19)
Only - Pulley/Nut/Washer And Blade
Bolt/Washers Not Included)
- - 532 44 42-69 Replacement Mower Complete