Husqvarna FE 350 2022 User Manual (English)

Questions and Answers:

K
Kara McdonaldAug 18, 2025
Why does my Husqvarna FE 350 2022 engine overheat?
- M
  mark87Aug 18, 2025
  If your Husqvarna Motorcycle engine overheats, there are several possible causes. Start by checking the coolant level and inspecting the cooling system for leaks. Ensure sufficient airflow and switch off the engine when stationary. Clean any dirt from the radiator fins. If there's foam in the cooling system, drain and refill the coolant. Also, check for a bent radiator hose and replace it if necessary. Finally, the thermostat might be defective and needs to be checked; the guideline opening temperature is 70 °C (158 °F).
C
Carol MilesAug 20, 2025
Why does my Husqvarna FE 350 2022 engine have too little power?
- D
  Douglas RobinsonAug 20, 2025
  If your Husqvarna Motorcycle engine has too little power, several factors could be responsible. The air filter may be heavily contaminated, requiring you to clean the air filter and air filter box. A very dirty fuel filter or fuel screen could also be the cause, so change the fuel filter or fuel screen. Additionally, an error in the electronic fuel injection could be the issue, necessitating a diagnostic check using the Husqvarna Motorcycles diagnostics tool.
L
laurenhendersonAug 23, 2025
What causes a Husqvarna Motorcycle engine not to speed up?
- K
  Kari FigueroaAug 23, 2025
  If your Husqvarna Motorcycle engine does not speed up, there are a couple of potential causes. An error in the electronic fuel injection could be the issue, which requires reading the fault memory using the Husqvarna Motorcycles diagnostics tool. Alternatively, a defective ignition system could be the problem, so check the ignition coil's secondary winding, the spark plug connector, and the stator winding of the alternator.
J
Jesus CarrollAug 26, 2025
What causes high oil consumption in a Husqvarna FE 350 2022 Motorcycle?
- S
  shaneclarkAug 26, 2025
  High oil consumption in your Husqvarna Motorcycle can stem from several causes. Check if the engine vent hose is bent, and if so, route it without bends or replace it. Ensure that the engine oil level is not too high. If the engine oil is too thin, change the engine oil and oil filter, and clean the oil screen. Lastly, worn piston and cylinder could be the issue, requiring you to measure the piston/cylinder mounting clearance.
J
Jessica CastilloAug 30, 2025
How to troubleshoot Husqvarna FE 350 2022 when the engine cannot be cranked?
- E
  Eric GoodwinAug 30, 2025
  If your Husqvarna Motorcycle engine cannot be cranked by the starter motor, several issues could be the cause. You may need to charge the 12-V battery, and check the charging voltage, open-circuit current and the stator winding of the alternator. Also, the main fuse might be blown and you may need to change it. Other potential problems include a defective starter relay or starter motor, which would need to be checked. Also, make sure you carry out the start procedure.
P
Pamela MartinSep 1, 2025
What to do if Husqvarna FE 350 2022 Motorcycle engine dies during the trip?
- M
  Matthew GilbertSep 2, 2025
  If your Husqvarna Motorcycle engine dies during the trip, it could be due to a few reasons. You might be lacking fuel, so refuel. Also, fuse 1 or fuse 4 might be blown, so change the fuses of individual electrical power consumers.
R
Rose CoffeySep 4, 2025
Why is the malfunction indicator lamp flashing on my Husqvarna FE 350 2022 Motorcycle?
- I
  Isaiah FritzSep 4, 2025
  If the malfunction indicator lamp lights up or flashes on your Husqvarna Motorcycle, it indicates an error in the electronic fuel injection. You should check the wiring for damage and electrical plug-in connectors for corrosion and damage. Also, read out the fault memory using the Husqvarna Motorcycles diagnostics tool.
R
robinkellerSep 7, 2025
Why is the 12-V battery discharged on my Husqvarna FE 350 2022?
- J
  Joseph SotoSep 7, 2025
  If the 12-V battery is discharged on your Husqvarna Motorcycle, it could be due to a couple of reasons. The 12-V battery may not be charging due to a problem with the alternator, so check the charging voltage and the stator winding of the alternator. Alternatively, there may be an unwanted electrical power consumer, so check the open-circuit current.
J
Jack WilsonSep 9, 2025
Why are the lights not working on my Husqvarna Motorcycle?
- A
  Andrea HicksSep 9, 2025
  If the high beam, low beam, tail light, position light, and license plate lamp are not working on your Husqvarna Motorcycle, it is likely that fuse 2 is blown. You should change the fuses of individual electrical power consumers.
S
Samantha CobbSep 12, 2025
Why are the horn, brake light, turn signal, and radiator fan not working on my Husqvarna Motorcycle?
- A
  Alicia DavidsonSep 12, 2025
  If the horn, brake light, turn signal, and radiator fan are not working on your Husqvarna Motorcycle, it's likely that fuse 3 is blown. Replace the fuses of individual electrical power consumers.

Husqvarna FE 350 2022 Specifications

General

Engine Type	Single cylinder, 4-stroke
Displacement	349.7 cm³
Bore x Stroke	88 mm x 57.5 mm
Compression Ratio	13.5:1
Starter	Electric starter
Transmission	6-speed
Front Suspension	WP XPLOR-USD, Ø 48 mm
Ground Clearance	370 mm
Seat Height	950 mm
Fuel Tank Capacity	8.5 liters
Weight (without fuel)	106.5 kg
Frame Design	Central double-cradle type in chrome molybdenum steel
Rear Suspension	WP XACT Monoshock with linkage
Front Brake	Disc brake 260 mm
Rear Brake	Disc brake 220 mm

Summary

Means of Representation

Symbols Used

Explains the meaning of various symbols used in the manual for clear communication.

Safety Advice

Use Definition and Intended Use

Defines the purpose and permitted uses of the vehicle for safe operation.

General Safety Instructions

Provides essential safety instructions and warnings for operating the motorcycle.

Degrees of Risk and Symbols

Identifies hazard levels and associated warning symbols for risk assessment.

Safe Operation Guidelines

Provides guidelines for safe riding practices and rider fitness.

Important Notes

Manufacturer Warranty and Service

Details warranty terms, service requirements, and the importance of proper maintenance.

View of Vehicle

Front Left View

Illustrates and labels key components from the front-left view of the vehicle.

Serial Numbers

Vehicle Identification Number (VIN)

Locates and identifies the Vehicle Identification Number (VIN) for registration.

Engine Number Location

Details the location and identification of the engine number.

Controls

Clutch Lever Operation

Describes the function and location of the clutch lever.

Stop Button Function

Explains the function and location of the stop button for engine control.

Combination Switch Functions

Describes the function and options of the combination switch.

Opening Fuel Tank Filler Cap

Provides instructions on how to safely open the fuel tank filler cap.

Combination Instrument

Instrument Overview

Provides a visual guide to the instrument panel layout and indicators.

Setting the Clock

Steps for setting the time display on the instrument cluster.

Preparing for Use

Advice on First Use

Crucial pre-ride checks and advice for new owners.

Engine Running-In Procedure

Guidelines for the engine break-in period to ensure longevity.

Vehicle Preparation for Difficult Conditions

Adjustments needed for riding in challenging environments like sand.

Riding Instructions

Pre-Ride Checks and Maintenance

Pre-ride checks to ensure safety and operational readiness.

Starting the Vehicle Safely

Step-by-step guide for starting the motorcycle engine safely.

Activating Traction Control

How to engage and disengage the traction control system.

Braking Techniques and Safety

Proper braking techniques and safety precautions.

Service Schedule

Required Maintenance Work

Lists essential maintenance tasks based on operating hours.

Recommended Maintenance Work

Outlines recommended maintenance at specific intervals.

Tuning the Chassis

Basic Chassis Setting Adjustment

How to adjust suspension based on rider weight.

Shock Absorber Damping Adjustment

Details adjustment of compression and rebound damping.

Fork Damping and Preload Adjustment

Instructions for adjusting fork compression, rebound, and spring preload.

Handlebar Position Adjustment

Detailed steps for adjusting handlebar position for ergonomics.

Service Work on the Chassis

Lifting and Securing the Motorcycle

Safe procedure for lifting the motorcycle using a stand.

Fork Leg Maintenance

Procedures for cleaning fork dust boots and removing fork legs.

Steering Head Bearing Service

Procedures for checking and adjusting steering head bearing play.

Shock Absorber Removal and Installation

Detailed procedures for removing and installing the rear shock absorber.

Air Filter and Air Filter Box Maintenance

Steps for removing and installing the air filter and its cover.

Fuel Tank Removal and Installation

Detailed steps for removing and installing the fuel tank.

Chain Maintenance and Adjustment

Procedures for cleaning, checking, and adjusting chain tension.

Hydraulic Clutch Fluid Service

Procedures for checking and changing hydraulic clutch fluid.

Brake System

Brake Disc Inspection

Procedure for checking brake disc thickness and condition.

Front Brake Fluid Level Check

How to check the front brake fluid level.

Front Brake Lining Service

Procedures for checking and changing front brake linings.

Foot Brake Lever Free Travel Check

How to check for proper free play in the foot brake lever.

Rear Brake Fluid Level Check

How to check the rear brake fluid level.

Rear Brake Lining Service

Procedures for checking and changing rear brake linings.

Wheels and Tires

Front Wheel Removal and Installation

Step-by-step guides for removing and installing the front wheel.

Rear Wheel Removal and Installation

Step-by-step guides for removing and installing the rear wheel.

Tire Condition and Pressure Checks

How to inspect tires for damage, wear, age, and maintain correct pressure.

Spoke Tension Check

Method to check and adjust spoke tension for wheel integrity.

Electrical System

12-V Battery Service

Procedures for removing, installing, and charging the 12V battery.

Fuse Replacement Procedures

How to replace main and individual circuit fuses.

Headlight Maintenance

Procedures for removing headlight assembly and changing bulbs.

Headlight Setting Adjustment

Procedure to check and adjust the headlight alignment.

Cooling System

Antifreeze and Coolant Level Checks

How to check coolant and antifreeze levels for engine health.

Coolant Draining and Refilling

Procedures for draining, refilling, and changing engine coolant.

Tuning the Engine

Throttle Cable Play Adjustment

How to check and adjust throttle cable free play for optimal response.

Engine Mapping and Idle Speed

Instructions for changing engine maps and adjusting idle speed.

Service Work on the Engine

Fuel Screen Replacement

Steps for replacing the fuel filter screen.

Engine Oil Level and Change

Procedure to check engine oil level and change oil/filter.

Cleaning and Care

Motorcycle Cleaning Procedure

Proper methods for cleaning the motorcycle's exterior.

Winter Operation Preparation

Procedures for preparing the motorcycle for winter storage or use.

Storage

Long-Term Motorcycle Storage

Guidelines for long-term storage of the motorcycle.

Preparing for Use After Storage

Steps to take before riding after a storage period.

Troubleshooting

Engine Cranking Issues

Diagnoses and actions for starter motor issues.

Engine Start Failure

Troubleshooting steps for when the engine cranks but won't start.

Engine Performance Issues

Addresses lack of acceleration, reduced power, and stalling.

Engine Overheating and Malfunction Lamp

Troubleshooting for overheating and interpreting malfunction indicator.

Blink Codes

Throttle Valve Position Programming

Indicates a needed adjustment for the throttle valve position.

Sensor Input Signal Faults

Identifies faults with sensors like crankshaft speed or coolant temperature.

Technical Data

Engine Specifications

Provides detailed specifications for the engine.

Engine Tightening Torques

Lists torque specifications for engine components.

Fluid Capacities

Lists fluid capacities for engine oil, coolant, and fuel.

Fork Technical Data

Technical specifications and adjustment ranges for the front fork.

Chassis Tightening Torques

Lists torque specifications for chassis components.

Substances

Brake Fluid Specifications

Specifies types and standards for brake fluid.

Coolant Requirements

Details requirements and types of coolant.

Recommended Engine Oil

Specifies the recommended engine oil grade and type.

Auxiliary Substances

Air Filter Cleaner

Lists recommended cleaners for the air filter.

Chain Cleaner

Lists recommended cleaners for the drive chain.

Greases and Sprays

Specifies recommended greases, sprays for maintenance.

Standards

JASO T903 MA2 Standard

Explains the JASO T903 MA2 standard for motorcycle engine oils.

Index of Special Terms

OBD Definition

Definition of On-board diagnosis system.

List of Symbols

Yellow and Orange Symbols

Explains the meaning of yellow/orange warning symbols.

Green and Blue Symbols

Explains the meaning of green/blue informational symbols.

Related product manuals

Husqvarna FE 350 2021

169 pages

Husqvarna FE 350 2023

161 pages

Husqvarna FE 350 EU 2020

165 pages

Husqvarna FE 350 2016

381 pages

Husqvarna FE 350 2014

279 pages

Husqvarna FE 350 2015

308 pages

Husqvarna FE 350 S 2016

381 pages

Husqvarna FE 350 EU 2016

381 pages

Husqvarna FE 350 AU 2016

381 pages

Husqvarna FE 350 EU

117 pages

Husqvarna FE 350s 2022

162 pages

Husqvarna FE 350s US 2022

162 pages

Husqvarna FE 350 2022 User Manual

Table of Contents

Questions and Answers:

Husqvarna FE 350 2022 Specifications

Summary

Means of Representation

Symbols Used

Safety Advice

Use Definition and Intended Use

General Safety Instructions

Degrees of Risk and Symbols

Safe Operation Guidelines

Important Notes

Manufacturer Warranty and Service

View of Vehicle

Front Left View

Serial Numbers

Vehicle Identification Number (VIN)

Engine Number Location

Controls

Clutch Lever Operation

Stop Button Function

Combination Switch Functions

Opening Fuel Tank Filler Cap

Combination Instrument

Instrument Overview

Setting the Clock

Preparing for Use

Advice on First Use

Engine Running-In Procedure

Vehicle Preparation for Difficult Conditions

Riding Instructions

Pre-Ride Checks and Maintenance

Starting the Vehicle Safely

Activating Traction Control

Braking Techniques and Safety

Service Schedule

Required Maintenance Work

Recommended Maintenance Work

Tuning the Chassis

Basic Chassis Setting Adjustment

Shock Absorber Damping Adjustment

Fork Damping and Preload Adjustment

Handlebar Position Adjustment

Service Work on the Chassis

Lifting and Securing the Motorcycle

Fork Leg Maintenance

Steering Head Bearing Service

Shock Absorber Removal and Installation

Air Filter and Air Filter Box Maintenance

Fuel Tank Removal and Installation

Chain Maintenance and Adjustment

Hydraulic Clutch Fluid Service

Brake System

Brake Disc Inspection

Front Brake Fluid Level Check

Front Brake Lining Service

Foot Brake Lever Free Travel Check

Rear Brake Fluid Level Check

Rear Brake Lining Service

Wheels and Tires

Front Wheel Removal and Installation

Rear Wheel Removal and Installation

Tire Condition and Pressure Checks

Spoke Tension Check

Electrical System

12-V Battery Service

Fuse Replacement Procedures

Headlight Maintenance

Headlight Setting Adjustment

Cooling System

Antifreeze and Coolant Level Checks

Coolant Draining and Refilling

Tuning the Engine

Throttle Cable Play Adjustment

Engine Mapping and Idle Speed

Service Work on the Engine

Fuel Screen Replacement

Engine Oil Level and Change

Cleaning and Care