Why is the cutting blade rotating at idle speed on my Husqvarna Cutter?
If the cutting blade of your Husqvarna Cutter is rotating at idle speed, the idle speed may be too high; adjust it accordingly. If the issue persists, the clutch may be defective, and you should speak to your service agent.
What causes overheating in my Husqvarna K 770 Cutter?
If your Husqvarna Cutter is overheating, the air intake or cylinder flanges may be blocked; clean them. Also, the drive belt tension might be insufficient; examine and adjust the belt tension. Furthermore, the clutch could be defective; always cut at full throttle. If none of these resolves the issue, examine the clutch and speak to your service agent.
What to do if the SmartGuard on my Husqvarna K 770 does not move freely?
If the SmartGuard on your Husqvarna Cutter does not move freely or retract properly, the moving parts of the SmartGuard may be clogged; clean them. Additionally, the springs of the SmartGuard may not be operating correctly; check and clean the springs.
Why is there so much dust when I use my Husqvarna K 770?
If you notice excessive dust during the operation of your Husqvarna Cutter, the water supply or water pressure may be insufficient. Check the water supply to the product.
What to do if Husqvarna Cutter blade rotates at idle?
If the blade of your Husqvarna Cutter rotates at idle, the idle speed might be too high, so adjust it. Another potential cause is a defective clutch, in which case you should contact your servicing dealer.
Explains various symbols displayed on the machine itself.
Details the information found on the machine's rating plate.
Details the three levels of warnings used in the manual.
Overview of the power cutter's design and key features.
Outlines the owner's duties regarding safe operation and knowledge.
States the manufacturer's right to modify products.
Details the reversible cutting head feature and its use.
Explains the semi-automatic belt tensioning system.
Highlights specific features for the K 770 Rescue model.
Identifies and labels various parts of the K 770 and K 770 OilGuard.
Identifies and labels various parts of the K 770 Rescue.
General safety warnings and equipment checks.
Explains and checks throttle lockout and stop switch.
Importance and checking of blade guard and vibration system.
Explains the muffler's function and inspection.
General warnings and advice regarding cutting blades.
Warnings and specs for blades on high-speed handheld machines.
Covers abrasive blades, diamond blades, and sharpening.
Importance of cooling diamond blades and checking side clearance.
Warnings for carbide blades and blade transport/storage.
Checks for spindle, bushing, and fitting the cutting blade.
Instructions for adjusting and fitting the blade guard.
Procedure to disengage the OilGuard system.
Steps to reverse the cutting head.
Information on using cutting trolley and wheel kit accessories.
Types of petrol and oil recommended for the machine.
Instructions for mixing petrol and oil correctly.
Safety precautions and steps for refueling the machine.
How OilGuard detects and handles incorrect fuel mixtures.
Guidelines for transporting fuel and storing the machine.
Details required personal protective equipment (PPE).
Basic safety directions and operator responsibility.
Safety considerations for the working area.
Explains fundamental techniques and warnings for cutting.
Covers cutting position, distance, supervision, dust management.
Specifics for using carbide blades in rescue ops.
Pre-operation checks for rescue blades and techniques.
Explains kickback causes, reactive force, and avoidance.
Special care and techniques for cutting pipes.
Simple steps to avoid kickback and store the cutter.
Pre-start checks and safety precautions.
Detailed steps for starting the engine with a cold engine.
Steps for starting the engine with a warm engine.
Procedure for stopping the engine.
General maintenance warnings and schedule.
Instructions for cleaning and spark plug maintenance.
Tensioning and replacing the drive belt.
Idle speed adjustment and starter housing safety.
Steps for poor engine power or acceleration.
Procedure for replacing and tensioning recoil spring.
Steps for fitting the starter assembly.
Checking and replacing fuel and air filters.
Checks for drive gear, clutch, water system, and disposal.
Table of common problems, probable causes, and solutions.
Specifications for cylinder, speed, power, fuel, and weight.
Measured noise and vibration levels.
Specs for abrasive and diamond cutting blades.
EU conformity statement and applied standards.
To Next Page
General