Reverse Neutral Fast Slow Choke Fuel Park Brake
Danger Use protective
glasses
Use protective
gloves
Wear hearing
protection
Do not
stand here
These symbols are found on the machine and in
the operator manual. Study them carefully until
you know what they mean.
WARNING! Xxxx xxxxxx xxxxx xxxx
xxxxxxxxx xxxxxx xxxxxxxxx.
Used in this publication to tell the reader of a
risk of personal injury or death, particularly if the
reader neglects to obey the instructions in the
manual.
IMPORTANT INFORMATION Xxxx xxxxxx
xxxxx xxxx xxxxxxxxx xxxxxx xxxxxxxxx.
Used in this publication to tell the reader of a
risk of material damage, particularly if the reader
neglects to obey the instructions in the manual.
Used also when there is a possibility for misuse or
misassembly.
RN
Read Operator
Manual
Shut off engine,
before maintenance
or repair
Keep a safe
distance from
the machine
Use on slopes no
greater than 10° No passengers
Whole body
exposure to
thrown objects
Severing of fi ngers
and toes
Do not open or
remove safety
shields wIth
engine running
Careful backing up,
watch for
other people
Careful going
forward, watch for
other people
Warning!
Battery acid is
corrosive, explosive
and fl ammable
Warning!
Do not
touch parts
Warning!
Keep away from
the discharge deck
Warning!
Do not use
without defl ector
or grass catcher
6
SYMBOLS AND DECALS
ORNILLOS HEXÁGONOS
Los valores de par indicados se deben utilizar como pauta general
cuando no se tenga información de los valores de par específi cos.
Tornillería estándar de EE. UU.
Grado SAE grado 5 SAE grado 8 Tornillo Flangelock con
tuerca Flangelock
Tamaño pies/lbs Nm pies/lbs Nm pies/lbs Nm
Tamaño de culata (diámetro en
pulgadas, rosca fi na o gruesa)
1/4 9 12 13 18
5/16 18 24 28 38 24 33
3/8 31 42 46 62 40 54
7/16 50 68 75 102
1/2 75 102 115 156
9/16 110 149 165 224
5/8 150 203 225 305
3/4 250 339 370 502
7/8 378 512 591 801
1-1/8 782 1060 1410 1912
** Grado 5 - Calidad comercial mínima (no se recomienda una menor calidad)
Tornillería estándar en sistema métrico
Grado Grado 8.8 Grado 10.9 Grado 12.9
Tamaño pies/lbs Nm pies/lbs Nm pies/lbs Nm
Tamaño de culata (diámetro en milímetros,
rosca fi na o gruesa)
M4 1.5 2 2.2 3 2.7 3.7
M5 3 4 4.5 6 5.2 7
M6 5.2 7 7.5 10 8.2 11
M7 8.2 11 12 16 15 20
M8 13.5 18 18.8 25 21.8 30
M10 24 33 35.2 48 43.5 59
M12 43.5 59 62.2 84 75 102
M14 70.5 96 100 136 119 161
M16 108 146 147 199 176 239
M18 142 193 202 274 242 328
M20 195 264 275 373 330 447
M22 276 374 390 529 471 639
M24 353 478 498 675 596 808
M27 530 719 735 996 904 1226
Sujetadores estándar 12 Nm
Sujetadores estándar 25 Nm
Sujetadores estándar 44 Nm
Sujetadores estándar 70 Nm
Sujetadores estándar 110 Nm
Perno del cigüeñal del motor 67 Nm
Tornillos de polea de corte 203 Nm
Tuercas del asa 102 Nm
Tornillo de la cuchilla 122 Nm
Especifi caciones de par
75
DATOS TÉCNICOS
To Next Page
Loading...
