Husqvarna PW 350 User Manual (English)

Other manuals for Husqvarna PW 350

Operator's Manual596 pages

User Guide12 pages

Questions and Answers:

A
Andrew ValentineAug 18, 2025
How to troubleshoot a Husqvarna PW 350 that won't start?
- G
  gutierrezwendyAug 18, 2025
  If your Husqvarna Pressure Washer isn't starting, check these potential causes: * Ensure the power plug is securely connected to a functioning power source. * Verify the power switch is in the on (I) position. * The thermal protector may have stopped the power. If so, allow the product to cool down before attempting to use it again. * Confirm that you are using the correct type of extension cable, fully unwound, and that its voltage matches the product's voltage. If these steps don't resolve the issue, there may be no electricity in the power source, or the power cord could be damaged. In these cases, consult an approved electrician or service agent.
D
Daniel EspinozaAug 20, 2025
Why is the water pressure unsatisfactory on my Husqvarna PW 350 Pressure Washer?
- J
  jacksonstuartAug 20, 2025
  If the water pressure from your Husqvarna Pressure Washer is not satisfactory, consider the following: * Make sure there are no bends in the hoses. * Ensure the power switch is in the on (I) position. * Verify the product is correctly connected to the water source and that the water flow is sufficient. * Clean the water filter. * Bleed the system to remove any air. * Use the correct accessory.
A
annamccormickAug 23, 2025
How to fix a Husqvarna Pressure Washer high-pressure water hose that is stuck?
- M
  Mrs. Rebecca JohnsonAug 23, 2025
  If the high-pressure water hose on your Husqvarna Pressure Washer is not possible to pull out, the hose reel is likely blocked. Remove the hose reel cover, remove the blockage, and clean the hose reel.
O
omooreAug 26, 2025
What to do if the display does not start on my Husqvarna PW 350 Pressure Washer?
- C
  Christopher WoodAug 26, 2025
  If the display on your Husqvarna Pressure Washer doesn't start when you turn the power switch to the ON (I) position, the power plug may not be connected to a power source. Connect the power plug to a power source.
R
Richard LarsonAug 28, 2025
Why does my Husqvarna PW 350 become too hot?
- M
  Mary BullockAug 28, 2025
  If your Husqvarna Pressure Washer becomes too hot, the air flow may not be sufficient. Clean the air intakes.
F
fdominguezAug 30, 2025
What to do if my Husqvarna PW 350 Pressure Washer does not operate smoothly?
- M
  Melinda GrayAug 31, 2025
  If your Husqvarna Pressure Washer doesn't operate smoothly, there might be air in the system. Bleed the system to resolve this.
D
danielmooreSep 1, 2025
Why does the fuse blow during start or operation of my Husqvarna Pressure Washer?
- A
  alexanderchristinaSep 1, 2025
  If a fuse blows during the start or operation of your Husqvarna Pressure Washer, ensure that you are using a slow-blow fuse that has class "C" or "K".
R
Robert OrozcoSep 4, 2025
What causes leakage in the couplings of my Husqvarna PW 350?
- P
  Paul MosleySep 4, 2025
  If there is leakage in the couplings of your Husqvarna Pressure Washer, the O-rings are likely worn or damaged. Replace the O-rings.
J
Jeffrey CooperSep 6, 2025
What to do if my Husqvarna PW 350 Pressure Washer does not stop?
- S
  Sabrina BarrettSep 7, 2025
  If your Husqvarna Pressure Washer does not stop, disconnect the power plug and speak to an approved service agent because the product is defective.
J
Jonathan JonesSep 9, 2025
What does the red temperature symbol on my Husqvarna PW 350 mean?
- J
  Jenna FreemanSep 9, 2025
  To address the red temperature symbol on your Husqvarna Pressure Washer, consider the following: * Ensure the ambient temperature is 4 °C or more during operation. * Store the product in a dry, frost-free environment where the temperature is above 0 °C. * Verify the water inlet temperature does not exceed 40 °C.