Need help?Do you have a question about the Husqvarna Rider Pro 18 and is the answer not in the manual?
General| Engine Manufacturer | Briggs & Stratton |
|---|---|
| Engine Power | 18 hp |
| Cylinders | 2 |
| Fuel Type | Gasoline |
| Fuel Tank Volume | 12 liters |
| Transmission Type | Hydrostatic |
| Cutting Height | 25 - 75 mm |
| Deck Material | Steel |
| Cutting Width | 112 cm |
Guidelines for driving and transporting the machine on public roads.
Precautions and procedures for towing the machine.
Defines the machine's purpose and user qualifications.
Importance of authorized dealers for support and service.
Location and importance of machine serial numbers for parts.
General guidelines for safe operation and user responsibilities.
Safety precautions for operating the machine on inclines.
Precautions to protect children from machine hazards.
Safety measures to be taken during maintenance.
Warnings and precautions related to fuel and battery handling.
General safety checks, fire risk reduction, and transport guidelines.
Explains various symbols used on the machine and in the manual.
Details crucial safety symbols and their meanings.
Introduction to Rider Pro 15 and Pro 18 models.
Explanation of the two-pedal speed control system.
Describes different cutting units and their functions.
Identifies and explains controls for the Pro 15 model.
Identifies and explains controls for the Pro 18 model.
Controls for engine speed, cold starting, and engine hours.
Controls for cutting unit height adjustment.
Controls for parking, seat adjustment, and refueling.
Controls for engine speed, cold starting, and engine hours.
Controls for cutting unit height adjustment.
Controls for parking, seat adjustment, and lighting.
Advice for optimal mowing results and machine care.
Mechanism to allow manual movement when the engine is off.
Pre-operation checks and adjustments.
Step-by-step guide to starting the engine.
Instructions on how to operate the machine.
Procedure for safely shutting down the engine.
Pre-operation checks and adjustments.
Step-by-step guide to starting the engine.
Instructions on how to operate the machine.
Procedure for safely shutting down the engine.
Table detailing maintenance tasks and intervals.
Steps to remove engine and transmission covers for service.
Steps to remove front and fender covers.
Procedures for checking and adjusting steering wire tension.
Steps to adjust the parking brake for proper function.
Procedures to adjust throttle and choke cables.
Guide to replacing the fuel filter on Pro 15 and Pro 18.
How to check and clean the fuel pump air filter.
Cleaning air intake grilles for proper engine cooling.
Instructions for replacing the air filter on Pro 15.
Instructions for replacing the air filter on Pro 18.
Procedures for cleaning engine and muffler to prevent fire risk.
How to check and maintain battery acid levels.
Spark plug service.
Verifying the function of safety interlocks.
Guide for replacing light bulbs on the Pro 18 model.
Location and types of fuses.
Recommended tyre pressures for optimal performance.
Step-by-step guide to attach the cutting unit.
Procedure to install the BioClip 90 attachment.
Steps to detach the cutting unit from the machine.
Adjusting the cutting unit's pressure for best results.
How to set the cutting unit's height.
Procedure to ensure the cutting unit is level.
How to adjust the cutting unit's angle.
Guide to replace the drive belt for the BioClip 90.
Detailed steps for BioClip 90 belt replacement.
Steps to change the belt on Combi 103.
Detailed steps to put the cutting unit in service position.
How to check blade condition and tightness.
How to replace the break-pin for blade protection.
Steps to remove the BioClip plug for other cutting modes.
Diagram showing lubrication points and intervals for Pro 15.
Diagram showing lubrication points and intervals for Pro 18.
General lubrication tips and precautions.
How to lubricate control wires.
Lubricating the cutting unit's joints and bearings.
Lubricating pedal mechanisms in the frame tunnel.
Lubricating chains, triangular links, and seat mechanisms.
Lubricating controls, levers, and belt tensioner.
Checking and filling engine oil.
Procedure for draining and changing engine oil.
Lubricating the gear lever and hydrostatic wire.
Lubricating brake wire and checking transmission oil.
Guide to replacing the engine oil filter.
Steps to change the hydraulic oil filter.
Common causes and solutions for engine starting issues.
Troubleshooting engine running and power issues.
Causes and remedies for engine overheating and battery problems.
Troubleshooting machine vibration and uneven mowing.
Instructions for preparing the machine for winter.
Recommendations for seasonal service.
Identifies electrical components and wire colors for Pro 15.
Identifies electrical components and wire colors for Pro 18.
Specifications for dimensions and engine details.
Specifications for various cutting units (width, height, weight).
Statement of compliance with EU directives.
Checklist for pre-delivery inspection and setup.
Maintenance tasks for 25, 50, 100/200, 300 hour services.
Seasonal maintenance tasks and their intervals.
To Next Page