Need help?Do you have a question about the Husqvarna Rider 15V2 and is the answer not in the manual?
General| Manufacturer | Husqvarna |
|---|---|
| Type | Rider |
| Model | 15V2 |
| Net Power RPM | 3600 RPM |
| Deck Material | Steel |
| Transmission | Hydrostatic |
| Fuel Type | Gasoline |
| Fuel Tank Capacity | 12 L |
| Warranty | 2 years |
| Cutting Width | 95 cm |
| Drive | Rear Wheel Drive |
| Cutting Height | 25-70 mm |
Guidelines for safe operation of the ride-on mower, covering general use and precautions.
Precautions and procedures for safe operation on slopes to prevent tip-overs and loss of control.
Safety measures to prevent accidents involving children near the machine during operation.
Safety precautions to observe before performing maintenance or service on the machine.
Guidelines for safe road travel, transport, and towing the machine to prevent damage.
Specifies the designed purpose and proper usage, including operational and safety procedures.
General safety advice and best practices for operating ride-on mowers effectively.
Regulations and procedures for driving or transporting the machine on public roads.
Instructions for towing the machine to prevent potential damage to the transmission.
Defines the machine's designed purpose and specifies conditions for proper operation.
Information about authorized dealers and obtaining the best support and service.
How to locate and state the serial numbers for the machine, engine, and transmission.
Step-by-step instructions for safely starting the engine.
Essential safety practices for general operation of the mower, including clearing the area.
Critical safety precautions and procedures for operating the machine on slopes.
Measures to ensure child safety around the machine during operation and maintenance.
Safety precautions to observe before performing any maintenance or service on the machine.
Identifies and describes the location of all major machine controls for easy access.
Explains the function and operation of the throttle control for engine speed.
Describes the use of the choke lever for cold starting and richer fuel mixture.
How the speed limiter and driving pedals control machine speed for forward and reverse.
Step-by-step instructions for applying and releasing the parking brake.
Information about the different cutting units available for the Rider 15V2.
How to operate the lift lever for raising and lowering the cutting unit.
How to adjust the cutting height using the dedicated lever.
Details on adjusting the seat lengthways for operator comfort.
Instructions and precautions for safely fueling the machine's fuel tank.
Pre-operation checks and reading instructions before starting the engine.
Step-by-step guide to starting the engine safely and correctly.
How to operate the machine's driving controls for forward and reverse movement.
Advice and techniques for achieving optimal mowing results.
Procedures for safely stopping the engine and securing the machine.
Explains the function of the release lever for moving the machine when the engine is off.
Overview of maintenance intervals and tasks for regular upkeep of the machine.
Instructions for removing machine hoods and fenders for maintenance access.
How to check and adjust the tension of the steering wires.
Step-by-step guide to adjusting the machine's brake for optimal performance.
How to check and adjust the throttle control cable for proper engine response.
How to check and adjust the choke control cable for starting.
Procedure for replacing the fuel filter at recommended intervals.
Step-by-step instructions for removing, cleaning, and replacing the air filter.
How to check and clean the fuel pump's air filter for proper function.
Procedure for checking and topping up the battery acid level with distilled water.
Maintenance of the ignition system, focusing on spark plug inspection and replacement.
How to inspect and verify the proper function of the machine's safety systems.
Location and procedure for checking and replacing the main fuse.
Procedure for checking and setting the correct tyre pressure for optimal performance.
How to clean the engine's cooling air intake for efficient cooling.
Step-by-step instructions for correctly fitting the cutting unit to the machine.
Procedure for safely removing the cutting unit from the machine.
How to check and adjust the cutting unit's ground pressure for optimal cutting.
How to check the cutting unit's parallelism to ensure proper mowing.
Procedure for adjusting the cutting unit's parallelism for optimal results.
Instructions and steps for replacing the cutting unit drive belts.
Procedure for changing the drive belt on units with side ejection and Combi 112.
How to place the cutting unit in the service position for easy access.
Steps to correctly return the cutting unit from the service position.
How to check the condition, sharpness, and tightness of the cutting blades.
Procedure for replacing the break-pin on Combi 103 units to protect the drive.
How to remove the BioClip plug for converting to rear ejection.
How to check and maintain the engine oil level correctly.
Procedure for changing the engine oil at recommended intervals.
Steps for replacing the engine oil filter.
How to check the transmission oil level.
Instructions on how to lubricate the belt adjuster.
Guidance on general lubrication points and recommendations for the machine.
Specific steps for preparing and storing the machine during winter.
Information about a protective cover for machine storage or transport.
Guidance on annual inspection and using genuine parts for longevity.
Checklist of tasks performed before machine delivery to the customer.
Initial maintenance task required after the first 8 hours of operation.
To Next Page
