Husqvarna SOFF-CUT 150 User Manual

Husqvarna SOFF-CUT 150

100 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Soff-Cut 150, Soff-Cut 150 D

EN Operator's manual 2-32

ES-MX Manual del usuario 33-64

FR-CA Manuel d’utilisation 65-96

Questions and Answers:

H
heather02Sep 9, 2025
What to do if Husqvarna Construction Equipment pulls to one side?
- L
  Lauren WestSep 9, 2025
  If your Husqvarna Construction Equipment (Soff-Cut 150D) pulls to one side while sawing, check the alignment of the front and rear pointers with the center of the cutting blade. Also, check the cutting blade for any signs of wear or damage. Avoid twisting or moving the product to the sides during operation, and ensure all wheels move freely and smoothly. Allow the cutting blade to operate at its correct speed without applying excessive force.
C
Christine Nguyen DDSSep 10, 2025
How to stop Husqvarna Construction Equipment from pulling to the side?
- B
  Brittney AvilaSep 12, 2025
  To prevent your Husqvarna Construction Equipment (Soff-Cut 150) from pulling to the side during operation, ensure the front pointer is correctly aligned with the center of the cutting blade. Also, examine the skid plate for any damage or burrs.
R
Roger MorrisSep 12, 2025
What to do if my Husqvarna Construction Equipment engine does not start?
- D
  Dr. Cathy Vaughan MDSep 12, 2025
  If the engine of your Husqvarna construction equipment doesn't start, verify that there is fuel in the tank and that it is the correct type, without water. Ensure the fuel valve and the ON/OFF switch are in the "ON" position. Check the spark plug cable connection. For a flooded engine, adjust the choke. When starting cold, ensure the choke is in the "ON" position. Also, check the oil level, as a low level can stop the engine. Make sure the air filter isn't dirty or clogged, and confirm the blade shaft rotates freely, without concrete buildup in the blade block.
P
Patrick KirbySep 14, 2025
Why does my Husqvarna Construction Equipment pull to the side?
- A
  Annette PatelSep 14, 2025
  If your Husqvarna Soff-Cut 150 construction equipment pulls to the side during operation, check that the front pointer is correctly aligned with the center of the cutting blade. Also, examine the skid plate for any damage or burrs.

Husqvarna SOFF-CUT 150 Specifications

General

Brand	Husqvarna
Model	SOFF-CUT 150
Category	Saw
Language	English

Summary

Introduction

Owner Responsibility

Details the responsibilities of the owner/employer regarding product knowledge and safe operation.

Intended Use

Specifies the product's professional use for sawing concrete contraction joints and limitations.

Safety

Safety Instructions for Operation

Details critical safety procedures during product operation.

Personal Protective Equipment

Specifies mandatory protective gear for safe operation.

General Safety Instructions

Provides essential safety guidelines for operating the product.

Work Area Safety

Outlines safety precautions for the environment where the product is used.

Safety Devices on the Product

Fuel Safety

Exhaust Fumes Safety

Vibration Safety

Dust Safety

Noise Safety

Safety Instructions for Maintenance

Assembly

Assembling Cutting Blade and Skid Plate

Operation

Before Operating the Product

Working with Dust

Operating the Soff-Cut 150D

Instructions for operating the Soff-Cut 150D model.

To Fill Fuel

Instructions and safety precautions for refueling the product.

Connecting Dust Extractor

To Stop the Engine

Steps for safely shutting down the product's engine.

To Start the Engine

Step-by-step guide for starting the product's engine.

Operating the Soff-Cut 150

Instructions for operating the Soff-Cut 150 model.

Maintenance

Maintenance Schedule

Provides a schedule for routine maintenance tasks based on usage hours.

Removing the Blade

Installing a Cutting Blade

Instructions and warnings for installing a new cutting blade.

Adjusting Blade Depth (Soff-Cut 150D)

Cleaning the Product Externally

Checking Oil Level

Steps for checking the engine oil level and warnings.

Replacing Engine Oil

Procedure for draining and refilling engine oil.

Air Filter

Troubleshooting

Product Causes Chipping, Spalling, or Ravelling (Soff-Cut 150)

Product Causes Bevel or Radius Cuts (Soff-Cut 150D)

Engine Does Not Start

Common issues and solutions for an engine that fails to start.

Product Pulls Sideways During Operation (Soff-Cut 150)

Engine Operates Poorly or at Reduced Speed

Diagnosing and fixing engine performance issues.

Product Pulls Sideways While Sawing (Soff-Cut 150D)

Transportation, Storage, and Disposal

Transportation

Lifting the Product

Storage

Related product manuals

Preview: Husqvarna Soff-Cut 2500

Husqvarna Soff-Cut 2500

Preview: Husqvarna 390

Preview: Husqvarna K960

Preview: Husqvarna K750

Preview: Husqvarna 4000

Preview: Husqvarna TS 60

Husqvarna TS 60

Preview: Husqvarna FS 413

Husqvarna FS 413

Preview: Husqvarna FS400LV

Husqvarna FS400LV

Preview: Husqvarna FS5000 D

Husqvarna FS5000 D

Preview: Husqvarna FS7000 D

Husqvarna FS7000 D

Preview: Husqvarna K 970 Rescue

Husqvarna K 970 Rescue