Husqvarna YTH2246 - Chassis

TRACTOR ==MODEL NUMBER 917.287541, PRODUCT NO. YTH2246
CHASSIS
KEY PART
NO. NO. DESCRiPTiON
3 532 40 50-12 Logo Crown
5 532 40 87-02 Dash
14 532 41 10-46 Hood
15 532 19 89-07 Lens LH
18 532 40 86-07 Grille/Lens Asm,
25 532 19 89-06 Lens RH
34 532 19 61-25 Plate Engine
36 8170605-12 Screw 5/16-18 x 3/4
37 532 40 47-94 Fender
52 873 68 05-00 Nut Lock 5/16-18
68 817 49 05-08 Screw Thdrol 5/16-18 x 1/2
99 532 40 59-03 Rod Asm Bypass
130 532 19 16-11 Screw 10 x 3/4 Single Lead-Hex
138 532 40 29-54 Cupholder
150 532 19 85-12 Air Duct
152 532 19 95-35 Shield Browning
162 532 14 24-32 Screw
175 532 19 63-04 Crossmember
176 532 40 07-76 Screw 10-24 x 5/8
177 532 19 52-27 Bushing Steering
178 532 19 97-82 Cargo Net Asm,
180 532 19 54-57 Chassis
181 532 40 30-25 Bushing Mtg, Fender Crgo
182 532 19 47-87 Dash Lower
183 8747805-20 Bolt Fin Hex 5/16-18 unc x 1-1/4
189 8170005-12 Screw 5/16-18 x 3/4
194 873 90 05-00 Nut Lock Hex Flange 5/16-18
195 532 40 41-37 Plug Hole Dash Lower
196 532 40 28-43 Console Asm, Deck Lift
202 532 40 30-48 Vent Side Hood RH
203 532 40 30-76 Vent Side Hood LH
204 532 40 05-39 Vent Top Hood
205 532 40 17-09 Skirt Hood Side RH
206 532 40 17-11 Skirt Hood Side LH
207 532 19 71-98 Bezel RH
208 532 19 71-99 Bezel LH
209 532 19 91-30 Insert Hex Top RH
210 532 19 91-31 Insert Hex Top Lh
211 532 19 91-32 Insert Hex Bottom RH
212 532 19 91-33 Insert Hex Bottom LH
213 8747605-12 Bolt 5/16-18 x 3/4
214 532 19 91-45 Clip RetainerTinner
217 532 15 65-24 Rod Pivot
218 532 19 63-95 X-Piece Hood Stop
222 532 13 77-29 Screw Thdrol 1/4-20 x 5/8
228 532 19 51-61 Stud Fastner
230 532 17 01-65 Bolt Shoulder 5/16-18
234 532 40 47-42 Bumper Hood
235 532 40 61-29 Spacer Fender
236 873 93 05-00 Nut Lock 5/16-18 UNC
238 532 40 86-06 Trim Husq,
239 532 11 04-52 Nut Push
NOTE: All component dimensions given in U,S, inches
1 inch = 25,4 mm
31