To Next PageTo Next PageWhy is the water box empty or filling slowly in my HydraMaster Titan 575?
If the water box is empty or fills slowly, it could be due to a restriction in the water supply system (inspect the supply system from the source through the incoming quick connect) or a faulty float valve in the water box (disassemble and inspect the valve, repair or replace as necessary).
What to do if my HydraMaster Vacuum Cleaner engine will not turn over?
If your HydraMaster Vacuum Cleaner engine isn't turning over, start by checking the battery terminals for looseness or corrosion; clean and tighten them if needed. The battery might be dead, so try recharging or replacing it, and test the charging system. Also, check the main fuse. If these steps don't work, the vacuum blower might be seized (attempt to turn the coupler by hand), the ignition switch could be faulty (test for power), the starter solenoid might be faulty (test for power in the "START" position), or the starter motor could be faulty (test for power in the "START" position). If none of these steps resolve the issue, consult a qualified service technician.
What to do if my HydraMaster Titan 575 Vacuum Cleaner is unable to achieve normal cleaning solution temperature?
If your HydraMaster Vacuum Cleaner isn't reaching the normal cleaning solution temperature, check the temperature control knob to ensure it's properly adjusted. Inspect the thermovalve for any faults. Also, excessive solution flow at the tool can be a cause, so inspect the cleaning tool jet for size and wear. Hard water scale buildup in the heat exchanger can also affect temperature, so descale the system. Check for blockages on the inlet side of the heat exchanger, and ensure the heat selector valve is in the "HOT" position.
What to do if my HydraMaster Titan 575 Vacuum Cleaner engine turns over but will not start?
If your HydraMaster Vacuum Cleaner engine turns over but doesn't start, first, check if the recovery tank is full and drain it if necessary. Inspect the recovery tank float for any faults. Check if fuel is reaching the carburetor by testing the fuel pump for power and inspecting the pump itself. If the engine is flooded, remove and dry the spark plug. Inspect the spark plugs for wear or dirt and replace if needed. If none of these steps work, consult a qualified service technician.
What to do if my HydraMaster Titan 575 Vacuum Cleaner has water in the exhaust?
If you notice water in the exhaust of your HydraMaster Vacuum Cleaner, it could be due to a few reasons. The recovery tank might be overfilled with water or foam, so inspect and drain the tank if needed. Condensation in the system, especially in cool, humid weather, can also cause this, but it should dissipate after a few minutes of running. A leaking heat exchanger could also be the culprit, so inspect and repair or replace it as necessary.
Why is there water in the exhaust of my HydraMaster Titan 575 Vacuum Cleaner?
Water in the truckmount exhaust can occur if the recovery tank has been filled with foam or overfilled with water (inspect and drain the tank if full). It can also be due to condensation in the system, which is more common in cool weather and humid climates and should dissipate after a few minutes of running. Alternatively, the heat exchanger may be leaking water, requiring inspection and repair or replacement.
Why does my HydraMaster Titan 575 Vacuum Cleaner engine run rough at high speed?
If the engine runs rough at high speed, the possible causes are: * Faulty spark plugs: Remove and inspect the plugs, clean or replace as necessary. * Faulty spark plug wires: Inspect the wires and connectors for damage or loose connections, repair or replace as necessary. * Inadequate fuel supply to the carburetor: Check for blockage in the filter. Repair or replace as necessary.
Why does my HydraMaster Vacuum Cleaner engine run rich (black smoke)?
If the engine runs rich (producing black smoke), it could be due to a dirty air filter (inspect and replace as necessary) or excessive back pressure (inspect for a clogged heat exchanger, dirty air filter, or a partially opened choke).
What to do if the vacuum blower on my HydraMaster Titan 575 is locked and will not turn?
If the vacuum blower on your HydraMaster Vacuum Cleaner is locked and won't turn, it could be due to rust buildup from inactivity. Try spraying penetrating oil into the blower and let it sit for at least an hour, then carefully use a pipe wrench on the outer diameter of the pulley on the coupler to free the blower lobes. If this doesn't work, there may be internal damage to the blower, and you should consult a qualified service technician.
Why won't the pump on my HydraMaster Titan 575 come up to normal cleaning pressure?
If the pump on your HydraMaster Vacuum Cleaner isn't reaching normal cleaning pressure, the pressure adjusting valve might be faulty, so inspect, repair, or replace it. Worn seals or valves in the pump could also be the cause, so test the pump output volume. Additionally, check for a loose pump belt and adjust or replace it if necessary, as the pump rpm might be too low.
General| Brand | HydraMaster |
|---|---|
| Model | Titan 575 |
| Category | Vacuum Cleaner |
| Language | English |
