6
Locking/Unlocking the Keypad
To enable the keypad lock, enter the Func menu by
pressing the
Func/OK key in the home screen, and then
go to “Settings -> KP Lock -> On”. After this feature is
enabled, keypad will get locked automatically when the
preset time (preset by the dealer) expires. To unlock the
keypad, press the
Func/OK key and then .
Apart from locking the keypad via menu, you can
lock the keypad quickly and temporarily by pressing
the
Func/OK key and then directly in the home
screen.
PIN Code Security and Changing
PIN code can prevent unidentified user from using your
terminal. To enable or disable the PIN Code feature,
enter the Func menu from the home screen by pressing
the
Func/OK key, then go to “Settings -> Security
-> PIN Code”. Every time you need to change the
settings, it is required to input the PIN code first (default
PIN code: 1234, preset by the dealer).
With this feature enabled, you will need to enter the
correct PIN code prior to operating the terminal after
turning it on. If you input the wrong code for continuous
3 times (predefined by the dealer), the
terminal will be
locked. In this case, you will need to enter the correct
PUK code (default PUK code: 12345678) to reset the
PIN code.
To change the PIN code, go to “Settings -> Security
-> ChangePIN” from the home screen, and input the
correct current PIN code prior to changing the code.
Managing the Contacts
Contact List
To view the list, go to the “Func. -> PhoneBook” from
the home screen.
New Contact
To add a new contact, you can enter the
Func menu
by pressing
Func/OK key and go to “PhoneBook”.
Then press the
Func/OK key to enter “Options -> New
Contact” to add a new contact: enter the contact’s
alias in the editing screen, and press the
Func/OK key
to enter the “Input No.” screen to input the contact
number. And press the
Func/OK key again to select the
call type (“Private No.”, “PABX” or “PSTN”).
Finally, press
Func/OK key to confirm.
Viewing the Memory
To view the phonebook memory, you can enter the
Func menu by pressing the
Func/OK key, and go to
“PhoneBook” menu; then press
Func/OK to enter
“Memory”.
Call Services
TMO
Individual Call
In TMO, an individual call can be initiated either as a
half-duplex call or full-duplex call, which can be received
without pressing any key (Direct Signaling) or by
pressing the
Answer/Call key or PTT (Hook Signaling).
Contact your dealer for such programming as well as
more details.
1. Initiating an Individual Call
●
Via Menu
In the home screen, press Func/OK key to enter
the “PhoneBook” or “Call Log” submenu,
and select a contact. Then press PTT to initiate
a half-duplex call, or press
to initiate a full-
duplex call.
●
Via Manual Dial
In the home screen, to initiate a half-duplex
individual call, input the number you want to
call through the keypad, and then press PTT.
To initiate a full-duplex individual call, input the
number you want to call through the keypad,
and press
repeatedly to select the call type
“Private No.”. Then press
to initiate a full-
duplex call.
Note:
●
Entry of individual numbers must comply
with the SSI&TSI dialing rules. See
“SSI&TSI Dialing Rules” in “Appendix”
for more details.
● Calls will end automatically if the
predefined call timer expires.
2. Answering an Individual Call
●
Half-duplex Individual Call
●
If it is an incoming call with Direct Signaling, there
will be an alert tone to inform the called party that
a call is received.
● If it is an incoming call with Hook Signaling, the
terminal sounds alert and vibrates to inform the
called party that there is an incoming call. And
to receive the call, the PTT key or Func/OK key
should be
pressed.
To take the talk rights during the call, there are
two situations: 1) if you have no pre-emptive
priority, hold down PTT to talk after the talking
party stops talking and releases its PTT; 2) if you
have already been programmed with pre-emptive
priority, hold down PTT to talk at any time.
●
Full-duplex Individual Call
●
If it is an incoming call with Direct Signaling, there
will be an a
lert tone to inform the called party that
a call is received.
●
If it is an incoming call with Hook Signaling, the
terminal sounds alert and vibrates to inform the
called party that there is an incoming call. And
to receive the call, the PTT, Func/OK key or
should be pressed.
After the call is established, both parties can talk
at any time, with no need to use any key.
3. Hanging up/ Rejecting an Individual Call
When initiating the in dividual call, pre s s the
O p t i o n s/ B a c k k e y o r t o t e r m i n a t e i t .
In the p re sence of an incomin g individ ual c al l,
To Next Page
Loading...
