Ice I18B - User Manual

Other manuals for Ice I18B

Operator's & Parts Manual33 pages

Questions and Answers

E
Eric Bolton DVMAug 13, 2025
What to do if Ice I18B has poor water pick up?
- R
  Roger ParksAug 13, 2025
  If your Ice Floor Machine isn't picking up water well, several factors could be at play. Start by checking the squeegee for clogs and clean it with a damp towel. Inspect the squeegee blades for wear and replace them if needed. Ensure the vacuum hoses are securely connected and free of holes, and clear any clogs from the vacuum hose. Also, make sure the drain hose stopper is tight, the vacuum motor mounting screws are snug (but not overtightened), and the recovery tank isn't full. Finally, check the float shut-off for any obstructions.
D
Darrell BarnettAug 16, 2025
Why Ice Floor Machine has no power?
- S
  Savannah CurtisAug 17, 2025
  If your Ice Floor Machine has no power, the issue might stem from a few potential causes. It could be due to incorrect or faulty wiring, a bad brush motor, or worn-out carbon brushes. In this case, check the wiring or contact an ICE Distributor.
L
Lori BrightAug 20, 2025
How to increase the runtime of Ice Floor Machine?
- B
  Barbara SandersAug 20, 2025
  A short runtime on your Ice Floor Machine could be due to several reasons. The battery charge might be low, so fully recharge the batteries. Defective batteries could also be the cause, requiring replacement. Another potential issue is a faulty battery charger, which would need repair or replacement.
L
Lori JenningsAug 25, 2025
What to do if the vacuum motor does not run on Ice Floor Machine?
- J
  Jodi RodriguezAug 25, 2025
  If the vacuum motor on your Ice Floor Machine isn't running, there are a few potential reasons. The wiring might be connected incorrectly or be faulty, the vacuum motor itself could be bad, or the carbon brushes might be worn out. In this case, check the wiring or contact an ICE Distributor.
E
Evan MillerAug 27, 2025
What to do if my Ice Floor Machine has poor water pick up?
- M
  masonsummersAug 27, 2025
  If your Ice Floor Machine isn't picking up water effectively, several factors could be the cause. Start by checking the squeegee for clogs and clean any debris with a damp towel. Inspect the squeegee blades for wear and replace them if necessary. Ensure the squeegee assembly is securely fastened. Examine the vacuum hoses for holes or loose connections; tighten connections or replace damaged hoses. Clear any clogs from the vacuum hose. Also, make sure the drain hose stopper is tight, the vacuum motor mounting screws are snug (but not overtightened), and the cover tank is securely in place. Don't forget to drain the recovery tank if it's full and clear any debris from the float shut off inside the recovery tank.
S
Scott HernandezAug 31, 2025
Why my Ice I18B Floor Machine has no power?
- D
  Daniel ParkerSep 1, 2025
  If your Ice Floor Machine has no power, the issue might stem from several causes. It could be due to incorrectly connected or faulty wiring, in which case you should check the wiring. The problem might also be a bad brush motor or worn-out carbon brushes.
J
Jared BaileySep 4, 2025
How to extend runtime of Ice I18B?
- M
  Michael ChenSep 4, 2025
  A short runtime for your Ice Floor Machine can be due to several reasons. The battery charge might be low, so ensure you fully recharge the batteries. Defective batteries could also be the culprit, requiring replacement. Additionally, the batteries may need maintenance. A faulty battery charger can also cause this issue; consider repairing or replacing it.
A
alex15Sep 8, 2025
Why does my Ice I18B have little or no solution flow?
- J
  Jennifer GutierrezSep 8, 2025
  If your Ice Floor Machine has little to no solution flow, it could be due to a bad ball valve or a bad solution valve. Another potential cause is the ball valve position needing adjustment; ensure the ball valve is in a horizontal position for maximum solution flow.