vi « FC4A MICROSMART USER’S MANUAL »
INDEX
ID1 code 28-4
of slave 0 28-27
ID2 code 28-4
identification 28-4
IDI 28-19
IMOV 9-5
IMOVN 9-6
indirect
bit move
9-8
bit move not 9-10
move 9-5
move not 9-6
initialization string 27-2, 27-3, 27-6
commands 27-8
initialize
data link
25-11
pulse M8120 6-12
initializing relay 5-42, 5-44
in-operation output M8125 6-12
input
condition for advanced instructions
8-5
data 28-35, 28-36
filter 5-24
internal circuit 2-6, 2-16, 2-24, 2-25, 2-40
LEDs 28-16
module 2-23, 30-7
terminal arrangement 2-26, 2-29
operating range 2-6, 2-16, 2-24, 2-25, 2-40
points 16-3
specifications
AC input module
2-25
CPU module 2-6, 2-16
DC input module 2-24
mixed I/O module 2-40
usage limits 2-24, 2-25
wiring 3-13
inrush current at power-up 3-16, 3-17
installation
and wiring
3-1
in control panel 3-11
location 3-1
installing
clock cartridge
2-67
communication
adapter
2-62
module 2-62
HMI module 3-3
memory cartridge 2-66
instruction steps 30-3
instructions
binary arithmetic
11-1
Boolean computation 12-1
coordinate conversion 19-1
data comparison 10-1
data conversion 14-1
dual/teaching timer 22-1
intelligent module access 23-1
interface 16-1
move 9-1
PID 21-1
program branching 18-1
prohibited 29-22
pulse 20-1
shift/rotate 13-1
user communication 17-1
week programmer 15-1
intelligent module access
instructions
23-1
status code 23-6
internal circuit
input
2-6, 2-16, 2-24, 2-25, 2-40
output 2-17, 2-33, 2-36
internal relay
for SwitchNet slaves
28-37
keep designation 5-4
interrupt
input
5-20
status M8140-M8143 6-13
program applicability 30-3
timer 5-22
interval compare greater than or equal to 10-4
IOREF 18-5
J JMP and JEND instructions 7-25
jump instructions 7-25
K keep
data error
29-5
designation 5-4
L L6 series digital I/O data allocation 28-35
LABEL 18-1
label 18-1
call 18-3
jump 18-1
return 18-3
ladder refresh type 2-43
LAPP’s cables 28-3
LAS 28-25
latch phase 16-1
LCAL 18-3
LDS 28-25
LDS.0 28-23
LED indicators 28-14, 28-16
line
connection
27-2
control signals RS232C 17-29
linear conversion 19-5
list
advanced instruction
8-1
basic instruction 7-1
type 30-7
list of
active slaves (LAS)
28-25
detected slaves (LDS) 28-25
peripheral fault slaves (LPF) 28-25
projected slaves (LPS) 28-25
LJMP 18-1
local mode 28-15
LOD and LODN instructions 7-2
long press 28-14
longitudinal redundancy check 17-36
LPF 28-25
LPS 28-25
LRC 17-36
To Next Page
Loading...
