Need help?Do you have a question about the IKEA VALSKAPT and is the answer not in the manual?
General| Brand | IKEA |
|---|---|
| Model | VALSKAPT |
| Category | Microwave Oven |
| Language | English |
Space to record model and serial numbers for future reference.
Shows where to find the product's identification plate.
Instruction to attach sales receipt for future reference.
Reminder about proper grounding before use.
Warning to disconnect power before installation.
Warning about mounting surface load capacity.
Restriction against island or peninsula installation.
Recommendation for two-person installation.
Details on voltage, amperage, and power rating.
Procedure for handling damage during shipment.
Customer responsibility for product damage.
Installer responsibility for product damage.
List of hardware parts in the packet.
List of extra parts included with the unit.
Minimum clearance from cooking surface to cabinet bottom.
Clearances for outside exhaust with varying cabinet depths.
Instructions for spacing units in deeper cabinets.
Requirements for cabinet width and clear space.
Guidance for preparing external exhaust.
Advice for installing under flat cabinets regarding cord clearance.
Reference to template details for installation.
Steps for unpacking the oven and removing the mounting plate.
Methods to locate wall studs for secure mounting.
Process for centering the mounting on a stud.
Instructions for positioning the plate under flat cabinets.
Instructions for positioning the plate under recessed cabinets.
Instruction to ensure the microwave is installed level.
Step for measuring cabinet overhang for alignment.
Step for marking a horizontal line for alignment.
Alignment instructions for mounting tabs.
Safety caution for handling sharp edges.
Steps for marking vertical and horizontal lines on the wall.
Instruction to find wall studs for plate mounting.
Drilling instructions for mounting plate attachment.
Important note to defer mounting plate installation.
Maximum allowed duct length for effective venting.
Guidance on efficient duct installation for optimal airflow.
Information on connecting the exhaust adaptor.
Requirement for transition adaptors with round ducts.
Explanation of how to calculate equivalent duct length.
Modification needed for the damper when using adaptors.
Example of ductwork for top exhaust installation.
Example of ductwork for back exhaust installation.
Type of ventilation for vertical top exhaust.
Type of ventilation for horizontal back exhaust.
Type of ventilation for recirculating air.
Information on the default shipment configuration.
Direction to relevant sections for external venting.
Key points regarding blower motor and wiring.
Information about recirculating models.
Direction to relevant sections for external venting.
Key points for top exhaust installation.
Visual guide on how to use toggle bolts.
Important check before tightening mounting plate.
Safety warning about pinching fingers.
Step for securing the mounting plate.
Requirements for preparing the top cabinet.
Safety warning for drilling cabinet bottoms.
Caution regarding blower unit wiring.
Step to secure the blower unit.
Step to replace the blower plate.
Step for attaching the exhaust adaptor.
Check for proper damper function before mounting.
Note on adjusting alignment after installation.
Recommendation for two-person installation for safety.
Important installation caution.
Guidance for metal cabinets regarding cord protection.
Recommendation for using filler blocks.
Warning about potential damage without filler blocks.
Step for attaching the oven to the cabinet.
Step for securing oven with screws.
Step for final tightening of screws.
Process for adjusting the exhaust adaptor.
Step for connecting the house duct.
Method for sealing duct joints.
Key points regarding blower motor and wiring.
Step to remove the blower plate.
Visual guide on how to use toggle bolts.
Important check before tightening mounting plate.
Safety warning about pinching fingers.
Step for securing the mounting plate.
Requirements for preparing the top cabinet.
Safety warning for drilling cabinet bottoms.
Step to rotate the blower unit.
Step to reroute blower unit wires.
Step to orient blower for back exhaust.
Step to remove knockout plates.
Step to reinstall the blower unit.
Caution regarding blower unit wiring.
Step to secure the blower unit.
Step to replace the blower plate.
Step for attaching the exhaust adaptor.
Recommendation for two-person installation for safety.
Important installation caution.
Guidance for metal cabinets regarding cord protection.
Recommendation for using filler blocks.
Warning about potential damage without filler blocks.
Step for hooking oven onto mounting plate.
Step for rotating oven into place.
Step for temporarily securing oven.
Step for attaching oven to cabinet.
Step for securing oven with screws.
Step for final tightening of screws.
Steps to attach the mounting plate to the wall.
Visual guide on how to use toggle bolts.
Important check before tightening mounting plate.
Safety warning about pinching fingers.
Step for placing and mounting the plate.
Step for securing the mounting plate.
Requirements for preparing the top cabinet.
Template adjustment for deep cabinets.
Safety warning for drilling cabinet bottoms.
Step to position the microwave for inspection.
Action to verify blower plate installation.
Recommendation for two-person installation for safety.
Important installation caution.
Guidance for metal cabinets regarding cord protection.
Recommendation for using filler blocks.
Step for hooking oven onto mounting plate.
Step for rotating oven into place.
Step for temporarily securing oven.
Step for attaching oven to cabinet.
Step for securing oven with screws.
Step for final tightening of screws.
Step to install grease filters.
Information about factory-installed charcoal filters.
Steps for replacing or installing a charcoal filter.
Safety step to disconnect power.
Step to access and remove screws.
Step to remove the old charcoal filter.
Step to insert the new charcoal filter.
Step to secure the new charcoal filter.
Step to reinstall the vent.
Final step to close door and reconnect power.
Verification of installation completion.
Step to remove packaging.
Step to install internal components.
Step to connect power to the outlet.
Visual reminder about grounding safety.
Step to restore electrical power.
Instruction to read supplementary documents.
Instruction to retain assembly documents for inspectors.
Action to complete and submit product registration.
Instruction to cut hole in rear wall for exhaust.
Caution about improper exhaust placement.
Minimum width requirement for installation.
Step for aligning holes with mounting plate.
Importance of locating studs for mounting.
Marking locations for toggle bolts.
Instruction to trim the template.
Emphasizes reading instructions before template use.
Purpose of the top cabinet template.
Step to assess cabinet type for template fit.
Note on cabinet features affecting template placement.
Step to position and tape the template.
Important check for template alignment.
Drilling instructions for cabinet template holes.
Safety warning for drilling cabinet bottoms.
Step to cut power cord hole in cabinet.
Step to cut exhaust hole for vertical venting.
Step to remove the template from the cabinet.
Step to create filler blocks for recessed cabinets.
Instruction to resume main installation steps.
To Next Page
