iLight SCI0405 User Manual

SCH0410
l Maximum Load: 40 Amp single phase @ 40ºC.
l Maximum Channel Current: 10 Amps.
l Supply: 230 volts -/+ 10% 50/60 Hz.
(optionally, 127 volt 60 Hz).
l Protection: 4 x 10 Amp MCB’s type C, 6KA rated.
SCH1210 - As 0410 but 3 phase + 12 x 10 Amp.
SCI0805
l Maximum Load: 40 Amp single phase @ 40ºC.
l Maximum Channel Current: 5 Amps.
l Supply: 230 volts -/+ 10% 50/60 Hz (same phase).
l Protection: 1 x 20 Amp Double pole input MCB’s
type C, 6KA rated.
SCH1200
l Maximum Load: There is no load control.
l Power switching is achieved by the DSI ballasts
themselves.
l Maximum Channel Current: Not applicable.
l Supply: 1 x 230 volts -/+ 10% 50/60 Hz.
l Protection: Thermal non resetting fuse.
SCH0410
Dimmed Outputs
l 4 x 1-10 volt at 0.1 Amp sink current per channel.
l 4 x Tridonic DSI outputs (uses electronic power
switching in ballasts).
Switched Outputs
l 4 x 230 volt 10A (inductive or resistive).
SCH1210
Dimmed Outputs
l 12 x 1-10 volt at 0.1 Amp sink current per channel.
l 12 x Tridonic DSI outputs (uses electronic power
switching in ballasts).
Switched Outputs
l 12 x 230 volt 10A (inductive or resistive).
SCI0805
Dimmed Outputs
l 4 x 1-10 volt at 0.1 Amp sink current per channel.
l 4 x Tridonic DSI outputs (uses electronic power
switching in ballasts).
l 4 x 5 Amp inductive.
Switched Outputs
l 4 x 230 volt 5A (inductive or resistive).
SCH1200T
Dimmed Outputs
l 12 x 0-10 volts at 0.1 Amp sink current per channel.
l 12 x Tridonic DSI outputs (uses electronic power
switching in ballasts).
Switched Outputs
l None.
Terminal Sizes
SCH0410, SCH1210, SCI0805
l Incoming supply, maximum cable size: 10mm
2
.
SI0805T
l Incoming supply, cable rated for 40 Amp or to
correspond to input supply voltage.
l Maximum cable size 10mm
2
.
SCH1200T
l Incoming supply, maximum cable size: 2.5mm
2
l Ballast output, maximum cable size: 12 pairs
2.5 mm
2
per circuit.
SCH0410S - Single pole 4 channels
SCH0410N - Neutral disconnect “
SCH0410D - Double pole “
SCH1210S - Single pole 12 Channels
SCH1210N - Neutral disconnect “
SCH1210D - Double pole “
SCI0805T - Single pole - Dual unit
SCI0805S - Single pole “
SCI0805N - Neutral disconnect “
SCH1200T - Terminals - 12 Channel, no relays
Common specifications as detailed on page
12 plus the following features:
Key Features
SCH0410S
l 40 Amp fully rated source controller.
SCH1210
l 120 Amp total box load on 4 circuits.
SCI0805
l 40 Amp total box load on 1 supply.
SCH1200
l A 12 channel device source controller.
l Suitable for both 0-10 volt analogue and DSI ballasts.
l Quiet operation.
Mechanical Data
SCH0410
l Weight: 4kg.
l Mains Cable Access: 4 x 25 mm, 4 x PG16 and 1 x
PG21knockouts.
l Control Cable Access: 1 x 25 mm, 1 x PG16
knockouts.
SCH1210
l Weight: 7.5kg.
UK version
l Mains Cable Access: 12 x 25 mm, 1 x PG29
knockouts.
l Control Cable Access: 1 x 25 mm knockout.
Euro version
l Mains Cable Access: 12 x PG16 and 1 x PG29
knockouts.
l Control Cable Access: 1 x PG16 knockout.
SCI0805
l Weight: 7.5kg.
l Mains Cable Access: 4 x 25 mm, 4 x PG16 and 1 x
PG21knockouts.
l Control Cable Access: 1 x 25 mm, 1 x PG16
knockouts.
SCH1200T
l Weight: 3kg.
l Mains Cable Access: 2 x 25 mm and 2 x PG16
knockouts.
l Control Cable Access: 1 x 25 mm and 1 x PG16
knockouts.
Electrical Data
Load Types
l 1-10volt HF Fluorescent, 100 per channel.
l DSI & DALI Fluorescent Ballasts
SCH0410 & SCI0805, 32 / channel. 128 / unit
SCH1210, SCH1220 & SCH1200T, 64 / channel; 128 / unit
l 0-10 volt Iris control 20K Ohm input).
l 1-10 volt Multi-Load transformers 100 (control only).
HF Ballast Controllers
15 of 23
INTELLIGENT CONTROLS

iLight SCI0405 Specifications

General

Brand	iLight
Model	SCI0405
Category	Controller
Language	English