Image IMTL41205.0 - User Manual

Questions and Answers

J
Jill RushAug 12, 2025
How to fix Image Treadmill when the power does not turn on?
- C
  cassandra38Aug 12, 2025
  If the Image Treadmill's power does not turn on, make sure that the power cord is plugged into a surge suppressor, and that the surge suppressor is plugged into a properly grounded outlet. Use only a single-outlet surge suppressor. After the power cord has been plugged in, make sure that the key is fully inserted into the console. Check the reset/off circuit breaker located on the treadmill frame near the power cord. If the switch protrudes, the circuit breaker has tripped. To reset it, wait five minutes and then press the switch back in.
A
Anthony ZhangAug 25, 2025
Why does my Image Treadmill walking belt slow down when I walk on it?
- M
  Matthew BellAug 25, 2025
  If the Image Treadmill's walking belt slows down when you walk on it, and it feels overtightened, it may decrease treadmill performance and damage the walking belt. Use only a single-outlet surge suppressor that meets all of the specifications. If the walking belt is overtightened, remove the key and unplug the power cord. Using the allen wrench, turn both rear roller bolts counterclockwise, 1/4 of a turn. When the walking belt is properly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking platform. Be careful to keep the walking belt centered. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes.
R
robertfoxAug 30, 2025
What to do if Image IMTL41205.0 Treadmill power turns off during use?
- J
  Janet FloydAug 30, 2025
  If the Image Treadmill's power turns off during use, check the reset/off circuit breaker on the treadmill frame near the power cord. If the circuit breaker has tripped, wait for five minutes and then press the switch back in. Also, make sure that the power cord is plugged in. If it is, unplug it, wait for five minutes, and then plug it back in. Remove the key from the console and reinsert it fully.
K
Kristen BlankenshipSep 5, 2025
What to do if the displays of Image Treadmill console do not function properly?
- K
  Kimberly WilsonSep 5, 2025
  If the displays of the Image Treadmill console do not function properly, remove the key from the console and unplug the power cord. Remove the screws from the hood, and carefully remove the hood. Locate the Reed Switch and the Magnet on the left side of the Pulley. Turn the Pulley until sure that the gap between the Magnet and the Screw, move the Reed Switch slightly, and then retighten the Screw. Re-attach the hood, and run the treadmill for a few minutes to check for a correct speed reading.
D
Derek McgeeNov 17, 2025
How to fix Image IMTL41205.0 Treadmill walking belt that is off-center or slips?
- M
  melissa75Nov 17, 2025
  If your Image Treadmill's walking belt is off-center, first remove the key and unplug the power cord. If the walking belt has shifted to the left, use the allen wrench to turn the left rear roller bolt clockwise 1/2 of a turn; if the walking belt has shifted to the right, turn the bolt counterclockwise 1/2 of a turn. Be careful not to overtighten the walking belt. Then, plug in the power cord, insert the key, and run the treadmill for a few minutes. Repeat until the walking belt is centered. If the walking belt slips when walked on, first remove the key and unplug the power cord. Using the allen wrench, turn both rear roller bolts clockwise, 1/4 of a turn. When the walking belt is correctly tightened, you should be able to lift each edge of the walking belt 2 to 3 inches off the walking pl...