In-situ Wireless TROLL Com - User Manual

2023-03-20 | 0031242
Wireless TROLL Com/Wireless Rugged TROLL Com
2
6
1
5
3
4
100% - 90%
90% - 75%
75% - 50%
50% - 25%
Less than 25%
Connection status indicator
USB connection
Cable connector
Dust cover for USB connection
On/O button
Battery charge status
indicator
Flashing red = The Wireless
TROLL Com, instrument, and
Bluetooth-enabled device are
not connected.
Continuous red = The Wireless
TROLL Com is connected to an
instrument, but not connected
to a Bluetooth-enabled mobile
device.
Flashing green = The Wireless
TROLL Com is connected to the
Bluetooth-enabled device, but is
not connected to an instrument.
Continuous green = The
Wireless TROLL Com, instrument,
and Bluetooth-enabled device
are connected.
Use the Wireless TROLL Com to connect an In-Situ instrument to a Bluetooth-enabled mobile
device and the VuSitu mobile app. The Wireless TROLL Com doesn’t have internal data storage.
It allows data transfer between an instrument and VuSitu (or Win-Situ 5 via a USB cable).
Plug your Wireless TROLL Com
into a PC for charging or setup.
Attach an instrument to the Wireless TROLL Com with a Rugged Cable
before connecting to VuSitu. When switching instruments, you may need to
turn the Wireless TROLL Com o and on again.
Press the button once to turn
the device on or o.
Wireless Rugged
TROLL Com
Information subject to change without notice. In-Situ, In-Situ logo, “Water Simplied”, VuLink, RDO, RuggedCable, TROLL,
BaroTROLL, HydroVu, VuSitu, Baro Merge, and Win-Situ are trademarks or registered trademarks of In-Situ Inc. ©2023. All
rights reserved. This product may be covered by patents identied at www.in-situ.com/patents

Summary

Wireless TROLL Com Device Overview

Device Components and Indicators

Explains USB connection, dust cover, on/off button, battery status, cable connector, and connection status indicators.

Charging and Connecting to VuSitu

Charging the Wireless TROLL Com

Details on opening dust cover, connecting USB cable, plugging into power source, and device light indicators.

Connecting to VuSitu Mobile App

Instructions for attaching an instrument, turning on the device, launching VuSitu, and successful connection.

Connecting to Win-Situ 5

Connecting and Syncing with Win-Situ 5

Steps for attaching an instrument, connecting the USB cable, and configuring Win-Situ for device connection and time sync.

Default Communication Settings

Lists common default communication settings for In-Situ instruments like Baud, Data bits, Parity, Stop bits, and Device Address.

Maintenance and Accessories

Rebooting the Wireless TROLL Com

Procedure to reboot the device if it doesn't respond while connected to a computer.

Wireless TROLL Com Accessories

Lists compatible accessories including USB cable, Twist-Lock cable, and Rugged TROLL cable.

Cleaning the Wireless TROLL Com

Guidelines for cleaning the device surface, avoiding the charging port, and cleaning connector pins with alcohol.

Safety and Specifications

Safety Information

Important safety precautions for using the Wireless TROLL Com, including environmental limits and handling.

Technical Specifications

Details on operating temperature, storage, dimensions, weight, materials, environmental rating, output, and protocol.

Overview

1. Function Description
2. Important Technical Specifications
3. Usage Features
4. Maintenance Features

The In-Situ Wireless TROLL Com/Wireless Rugged TROLL Com is a communication device designed to connect In-Situ instruments to Bluetooth-enabled mobile devices running the VuSitu mobile app, or to a PC via a USB cable for use with Win-Situ 5. This device facilitates data transfer but does not have internal data storage.

Function Description:

The primary function of the Wireless TROLL Com is to act as a bridge between an In-Situ instrument and a mobile device or PC. It enables users to transfer data from the instrument to the VuSitu app for analysis and management, or to Win-Situ 5 on a computer. The device supports Bluetooth® and USB output options, making it versatile for various field and office setups. It is powered by a 3.6 V 2.9AH Lithium rechargeable cell (UBBL39-FL) and requires a 5 VDC USB charger (1 A or 500 mA) for charging.

Important Technical Specifications:

• Dimensions: 16 x 4.3 x 3 cm (6.3 x 1.7 x 1.2 in.)
• Weight: 165 g (0.36 lb)
• Materials: Constructed from Polycarbonate / Acrylonitrile Butadiene Styrene blend, Silicon, Urethane, Stainless steel, Brass, Thermoplastic Vulcanizate, Polyurethane, Polyethylene, Acrylic Copolymer, Titanium, Polyetheretherketone, and FKM Fluoroelastomer for durability.
• Environmental Rating: IP67, indicating high resistance to dust and water ingress.
• Operating Temperature: -5 to 50° C (23 to 122° F) with 95% relative humidity, non-condensing.
• Storage Temperature: -20 to 50° C (-4 to 122° F) with 95% relative humidity, non-condensing.
• Output Options: Bluetooth®, USB.
• Communication Protocol: Android®: SPP Windows®: SPP or USB.
• Battery Life: A fully-charged device can run for up to 40-50 continuous hours.
• Warranty: 1 year.
• Certifications: CE, FCC (SSSBC127-X), WEEE, UKCA.
• Sensor Specifications (for internal sensors, if applicable, or for connected instruments):
  • Temperature: Accuracy ±2° C max, Range -20 to 70° C (-4 to 158° F), Resolution 0.1° C, Fixed sensor type, Response time < 30 seconds, Units Celsius or Fahrenheit, Method EPA 170.1.
  • Barometric Pressure: Accuracy ±3 mbar max, Range 300 to 1100 mbar, Resolution 0.01 mbar, Fixed sensor type, Instantaneous in thermal equilibrium response time, Units psi, kPa, bar, mbar, mmHg, inHg, Torr, atm, Piezoresistive method.

Usage Features:

• USB Connection (1): Located at the top of the device, this port is used for charging the Wireless TROLL Com or for connecting it to a PC for setup or data transfer via Win-Situ 5.
• Dust Cover for USB Connection (2): Protects the USB port from environmental elements.
• On/Off Button (3): A single press turns the device on or off.
• Battery Charge Status Indicator (4): A series of green and red LEDs indicate the battery level:
  • Four green LEDs: 100% - 90%
  • Three green LEDs: 90% - 75%
  • Two green LEDs: 75% - 50%
  • One green LED: 50% - 25%
  • One red LED: Less than 25%
• Cable Connector (5): This is where an In-Situ instrument is attached using a Rugged Cable. It's important to connect the instrument before connecting to VuSitu. When switching instruments, rebooting the Wireless TROLL Com may be necessary.
• Connection Status Indicator (6): A multi-color LED provides feedback on the connection status:
  • Flashing red: Wireless TROLL Com, instrument, and Bluetooth-enabled device are not connected.
  • Continuous red: Wireless TROLL Com is connected to an instrument, but not to a Bluetooth-enabled mobile device.
  • Flashing green: Wireless TROLL Com is connected to the Bluetooth-enabled device, but not to an instrument.
  • Continuous green: Wireless TROLL Com, instrument, and Bluetooth-enabled device are all connected.
• Connecting to VuSitu:
  • Requires the VuSitu mobile app (available on Google Play Store or Apple App Store).
  • Attach an instrument, turn on the Wireless Rugged TROLL Com, and launch VuSitu. The app will automatically connect.
  • To connect to a different instrument, press "Disconnect" in VuSitu, which then displays a list of available connections.
  • Once paired, VuSitu shows the "Connected Instrument" screen.
• Connecting to Win-Situ 5:
  • Attach an instrument to the Wireless TROLL Com with a Rugged Cable.
  • Connect the USB cable from the Wireless TROLL Com to your PC's USB port.
  • Open Win-Situ 5 and select "No" when prompted to connect to a device.
  • Configure communication settings: Go to Preferences > Com Settings, select "Serial Communications" radio button, choose the correct Com Port, and click the check mark.
  • Click the yellow connect button at the bottom right of the screen.
  • If prompted to sync device time or update firmware, click "Yes."
  • Default communication settings for In-Situ instruments are typically: Baud: 19200, Data bits: 8, Parity bits: Even, Stop Bits: 1, Device Address: 1, Mode: Modbus-RTU.
• Rebooting: If the device is unresponsive, disconnect it from power, turn it on, then hold the Power button until the bottom LEDs flash back and forth and turn off. Turn it back on and attempt to use.

Maintenance Features:

• Charging: Charge the battery after each use to avoid full discharges. Do not store the device in temperatures above 122°F (50°C).
• Cleaning:
  • Clean the surface of the Wireless TROLL Com with a damp cloth and mild soap.
  • Do not clean the charging port.
  • Clean dirty or corroded connector pins with alcohol.
  • Ensure all parts are fully dry before use.
• Safety: Do not submerge the device or your mobile device in liquid. Do not use in temperatures beyond specified ranges. The device is not serviceable; do not attempt to disassemble it. It is safe to use above 2000 m.

In-situ Wireless TROLL Com Specifications