Indesit DFO 3T133 A F User Manual (English)

Other manuals for Indesit DFO 3T133 A F

Questions and Answers:

T
Thomas RandallAug 15, 2025
Why Indesit DFO 3T133 A F Dishwasher won’t start or respond to commands?
- E
  Ethan RossAug 15, 2025
  If your Indesit dishwasher won't start or doesn't respond, ensure it's properly plugged into the socket. If there was a power outage, press the START/Pause button to resume the cycle as the dishwasher doesn't restart automatically. Also, make sure the door is fully closed until you hear a 'click'. If the door was opened for more than 4 seconds during a cycle, close it and press START/Pause. If the display shows F9 or F12 and the On/Off and START/Pause LEDs are blinking rapidly, switch the appliance off and on again after one minute. If the problem continues, unplug it for one minute, then plug it back in.
D
Douglas SellersAug 18, 2025
What to do if my Indesit Dishwasher won’t drain?
- C
  cfisherAug 18, 2025
  If your Indesit dishwasher isn't draining and the display shows F3 with the On/Off and START/Pause LEDs blinking rapidly, first wait until the wash cycle finishes. Then, check that the drain hose isn't bent. Also, inspect the sink drain pipe for any blockage and clean it if necessary. Lastly, the filter might be clogged with food residues, so clean the filter assembly.
T
Tiffany MedinaAug 22, 2025
Why Indesit Dishwasher is not filling with water?
- Z
  zoconnorAug 22, 2025
  If your Indesit dishwasher is not filling with water and the display shows F6 with both On/Off and START/Pause LEDs blinking rapidly, check that there is water in the water supply and that the tap is open. Also, ensure that the inlet hose is not bent. Finally, check the sieve in the water inlet hose for clogs and clean it. After checking and cleaning, turn the dishwasher off and on, and restart a new program.
T
Teresa ArroyoAug 26, 2025
Why Indesit Dishwasher doesn't fill with water?
- A
  Alan MendezAug 26, 2025
  If your Indesit dishwasher isn't filling with water, it could be due to several reasons. First, ensure that there is water in the water supply and that the tap is fully open. Another possible cause is a bent inlet hose; make sure the inlet hose isn't bent. Finally, the sieve in the water inlet hose might be clogged, so it may be necessary to clean it. After checking and cleaning, turn the dishwasher off and on, then restart a new program.
A
andersonjasmineAug 28, 2025
Why Indesit DFO 3T133 A F finishes cycle prematurely?
- V
  Veronica RojasAug 28, 2025
  If your Indesit dishwasher finishes the cycle prematurely and displays F15 with the On/Off and START/Pause LEDs blinking rapidly, check if the end of the drain hose is placed at the correct height. Also, check for siphoning into the home sewage system and install an air admittance valve if necessary. Finally, check the water supply for leaks or other issues that may be letting air inside.
E
Emily MooreSep 1, 2025
Why salt indicator is lit on my Indesit DFO 3T133 A F Dishwasher?
- K
  Krystal JenningsSep 1, 2025
  The salt indicator on your Indesit dishwasher may be lit because the salt reservoir is empty. Refill the reservoir with salt. Note that the salt indicator may remain lit for several wash cycles after refilling. Also, adjust the water hardness.
M
mary20Sep 4, 2025
What to do if Indesit DFO 3T133 A F finishes cycle early?
- B
  Becky SmithSep 4, 2025
  If your Indesit dishwasher is completing cycles prematurely, there are a couple of things you can check. First, verify that the drain hose is positioned at the correct height and is not siphoning into the home sewage system; if it is, install an air admittance valve. Also, check the water supply for leaks or other issues that might be introducing air.
M
Michael HoldenSep 7, 2025
Why Indesit DFO 3T133 A F Dishwasher makes excessive noise?
- M
  Mr. Kenneth ColeSep 7, 2025
  If your Indesit dishwasher is making excessive noise, it could be due to the dishes rattling against each other. Make sure to position the crockery correctly. Alternatively, an excessive amount of foam may have been produced because the detergent has not been measured out correctly or is unsuitable for dishwashers. Restart the dishwasher by pressing the DRAIN button and run a new program without detergent.
C
cynthiacohenSep 12, 2025
What to do if rinse aid indicator is lit on Indesit DFO 3T133 A F?
- P
  Peter WhiteSep 12, 2025
  The rinse aid indicator on your Indesit dishwasher may be lit because the rinse aid dispenser is empty. Refill the dispenser with rinse aid; the rinse aid indicator may remain lit for several wash cycles after refilling.

Indesit DFO 3T133 A F Specifications

General

Door color	Stainless steel
Cord length	1.3 m
Control type	Buttons
Product size	Full size (60 cm)
Built-in display	Yes
Inlet hose length	1.55 m
Custom panel-ready	-
Outlet hose length	1.5 m
Appliance placement	Freestanding
Control panel color	Black
Current	10 A
Connected load	1900 W
AC input voltage	220 - 240 V
AC input frequency	50 Hz
Energy efficiency scale	A to G
Power consumption (off)	0.5 W
Power consumption (left-on)	6 W
Water consumption per cycle	9.5 L
Energy consumption per cycle	0.833 kWh
Cycle time	190 min
Noise level	43 dB
Dishwashing programs	Cups 40°C, Eco 50°C, Hygiene, Intensive 65°C, Pre-wash, Quick
Left-on mode duration	12 min
Number of place settings	14 place settings
Number of washing programs	6
Wi-Fi controlled	No
Package weight	49000 g