How to fix Indesit DIS 04 that won't start?
If your Indesit Dishwasher isn't starting, check these potential issues: Ensure the plug is correctly inserted into the electrical socket and that there is power in your house. Verify that the dishwasher door is completely closed. Also, check if a delayed start has been programmed.
Why are my dishes not clean after using Indesit DIS 04?
If your dishes aren't getting clean in your Indesit Dishwasher, consider these possibilities: Avoid overloading the racks and ensure proper arrangement of crockery. Check that the sprayer arms can move freely. Select a more intensive wash cycle if the current one is too gentle. Make sure you're using the correct amount and type of detergent. Ensure the rinse aid compartment lid is properly closed. Inspect the filter for dirt or blockages, and check the refined salt level.
What to do if no water drains from Indesit DIS 04?
If water isn't draining from your Indesit Dishwasher, it could be due to several reasons: First, make sure the dishwasher cycle has finished. Check the water outlet hose for any bends. Inspect the drain duct for blockages. Also, the filter might be clogged with food residues.
Why Indesit DIS 04 Dishwasher not drying properly?
If your crockery isn't drying properly in your Indesit Dishwasher, it could be due to the rinse aid being used up or the dosage being too low. Check the rinse aid dispenser setting; it might not be high enough. Also, a wash cycle without a drying programme might have been selected.
Why Indesit DIS 04 Dishwasher leaves white film on dishes?
If your dishes and glasses have a white film or limescale after washing in your Indesit Dishwasher, it might be because the level of refined salt is low, or the dosage setting isn't right for your water hardness. Check that the salt dispenser lid is properly closed and that you haven't run out of rinse aid or that the dosage is too low. Also, consider that the crockery might be made from non-stick material.
What to do if Indesit Dishwasher shows shut off tap alarm?
If no water is entering your Indesit Dishwasher and the tap alarm is sounding, first check if there is water in the mains supply. Also, inspect the water inlet hose for any bends. Turn on the tap; the appliance should start after a few minutes. If beeps activated the appliance lock, switch off the machine using the ON/OFF button, turn on the tap, and switch the machine back on after 20 seconds. Then, re-programme the machine and restart the wash cycle.
Why Indesit Dishwasher leaves streaks on glasses?
If your dishes and glasses are streaked or have a bluish tinge after being washed in your Indesit Dishwasher, it's likely that the rinse aid dosage is too high.
How to fix Indesit DIS 04 water inlet hose alarm?
If your Indesit Dishwasher shows a water inlet hose alarm or indicates a blocked water inlet filter, switch off the appliance using the ON/OFF button. Shut off the water tap to prevent flooding and remove the plug from the electrical socket. Check the water inlet filter for blockages caused by impurities.
Why is my Indesit DIS 04 Dishwasher so noisy?
Excessive noise from your Indesit Dishwasher could be caused by dishes rattling against each other or the sprayer arms. Another possibility is an excessive amount of foam due to incorrect detergent dosage or using a detergent not suitable for dishwashers.
What does water loading solenoid valve malfunction alarm mean on Indesit DIS 04 Dishwasher?
If your Indesit Dishwasher displays a water loading solenoid valve malfunction alarm, switch off the machine using the ON/OFF button and switch it back on after a minute. If the alarm persists, turn off the water tap to prevent flooding, remove the plug from the electrical socket, and call for assistance.
Instructions for placing the appliance on a level floor and adjusting feet for stability.
Guidelines for connecting water hoses and electrical power, including safety precautions.
Guidance on preparing and running the initial wash cycle for the dishwasher.
Step-by-step guide to starting a wash cycle on the dishwasher.
Instructions on how to correctly measure and add detergent for optimal results.
A table detailing wash cycles, detergent usage, and durations for different soil levels.
Instructions on how to fill and adjust the rinse aid dispenser.
Guide on setting the water hardness level for optimal softener performance.
Instructions on how to fill the salt dispenser to prevent limescale.
Procedure for disconnecting water and electricity before cleaning or maintenance.
Important safety instructions for the use and operation of the appliance.
Tips for reducing water and energy consumption during wash cycles.
A list of common problems and their potential causes and solutions.
Troubleshooting steps for water intake issues and blocked inlet filters.
Details of the standard manufacturer's guarantee covering repairs for twelve months.
General| Door color | Not applicable |
|---|---|
| Appliance placement | Fully built-in |
| Control panel color | Stainless steel |
| Concealed heating element | Yes |
| Drying class | B |
| Washing class | A |
| Noise level | 54 dB |
| Number of place settings | 10 place settings |
| Number of washing programs | 4 |
| Water consumption per cycle | 10 L |
| Energy consumption per cycle | 1.01 kWh |
Weight and Dimensions| Depth | 550 mm |
|---|---|
| Width | 445 mm |
| Height | 820 mm |
To Next Page
