EasyManua.ls Logo

Inepro DMMetering PRO1 V11 Series - User Manual

Default Icon
16 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
PRO1 V11.xxx series MID
DIN rail single phase two wire energy meter
PRO1D V11.111
PRO1D V11.112
PRO1D V11.121
PRO1D V11.122
PRO1D V11.211
PRO1D V11.212
PRO1D V11.221
PRO1D V11.222
Version 1.12
Note: the picture on the frontpage is a meter from the series of this meter, it might not
be exactly the same as the meter you bought

Table of Contents

Questions and Answers

  • S
    Susan MillerAug 5, 2025
    What to do if there is no pulse output from Inepro Measuring Instruments?
    • J
      Jeremiah AndersonAug 5, 2025
      If the Inepro Measuring Instruments pulse output isn't working, first, verify that the external voltage source (Ui) is 5-27V DC using a voltage meter. The problem might be that the pulse output isn't supplied with DC power. Also, ensure the connection is correct: the 5-27V DC should connect to the collector (pin 20+), and the signal wire (S) to the emitter (pin 21-). The issue could be that the pulse output is not connected correctly. If these steps don't resolve the issue, there may be a fault inside the meter.
  • J
    Jesse MaldonadoAug 13, 2025
    What to do if the register doesn’t count on Inepro DMMetering PRO1 V11 Measuring Instruments?
    • J
      joneskatelynAug 14, 2025
      If the register on your Inepro Measuring Instruments isn’t counting, start by checking if the red consumption LED is flashing. The reason might be that there is almost no load connected to the meter. If the LED is not flashing, there may be a fault inside the meter.
  • N
    Nicholas SmithAug 25, 2025
    Why is the red consumption LED not flashing on my Inepro DMMetering PRO1 V11?
    • M
      Michael FernandezAug 25, 2025
      If the red consumption LED (PULSE LED) on your Inepro Measuring Instruments isn't flashing, it could be due to a few reasons. First, ensure a load is connected to the meter. The problem might be that there is no load connected to the meter. If a load is connected, use an Ohm-meter to check if the load value is very low, because the load on the line may be very low. If these checks don’t solve the problem, there may be a fault inside the meter.

Summary

Safety instructions

Information for your own safety

General safety information and warnings for meter operation.

Qualified personnel

Defines who is authorized for installation and operation.

Use for the intended purpose

Specifies the intended application and connection requirements.

Proper handling

Lists essential precautions for transport, installation, and operation.

Foreword

Exclusion of liability

States limitations of liability for errors or omissions in the manual.

Copyright

Outlines copyright restrictions and intellectual property rights.

Registered trademarks

Lists registered trademarks and acknowledges third-party trademarks.

MID certificate

CE certificates

Type number table

Performance criteria

Specifications

Basic errors

Description

Material

Lists the materials used for the meter's components.

Dimensions

Installation

Operation

Consumption indication

Describes the function of the LED indicator for power consumption.

Reading the meter

Explains how to read the consumption value from the register.

Mechanical register

Details the features of the mechanical register type.

Digital register

Details the features of the digital LCD register type.

Pulse output

Explains the function and connection of the pulse output.

Troubleshooting

Technical support

SOP Table

Inepro DMMetering PRO1 V11 Series Specifications

General IconGeneral
BrandInepro
ModelDMMetering PRO1 V11 Series
CategoryMeasuring Instruments
LanguageEnglish

Related product manuals