Why does my InfiniSolar 10KW Inverter show 'BUS soft start time out'?
If your InfiniSolar Inverter displays 'BUS soft start time out', it indicates that internal components have failed. Please contact your installer.
What should I do if my InfiniSolar Inverter displays 'Over load'?
If your InfiniSolar Inverter shows an 'Over load' error, it means the inverter is loaded with more than 110% of its capacity for too long. To resolve this, reduce the connected load by switching off some equipment.
What to do if InfiniSolar Inverter displays 'Bus voltage over'?
If your InfiniSolar Inverter shows a 'Bus voltage over' error, it is likely due to a surge. First, restart the inverter. If the error message remains, contact your installer.
What to do if my InfiniSolar 10KW Inverter displays 'Solar over current'?
If your InfiniSolar Inverter displays a 'Solar over current' error, it's likely due to a surge. First, restart the inverter. If the error persists, contact your installer.
What to do if my InfiniSolar 10KW Inverter displays 'INV over current'?
If your InfiniSolar Inverter displays 'INV over current', it is likely due to a surge. Restart the inverter. If the error message still appears, contact your installer.
Why does my InfiniSolar 10KW show 'Wire connection fault'?
If your InfiniSolar Inverter displays 'Wire connection fault', it means internal wires are loose. Please contact your installer.
Why does my InfiniSolar Inverter show 'INV voltage low'?
If your InfiniSolar Inverter displays 'INV voltage low', it indicates that internal components have failed. Please contact your installer.
Why does my InfiniSolar Inverter show 'INV voltage high'?
If your InfiniSolar Inverter displays 'INV voltage high', it indicates that internal components have failed. Please contact your installer.
What to do if my InfiniSolar Inverter displays 'OP voltage fault'?
If your InfiniSolar Inverter displays 'OP voltage fault', it means the grid is connected to the output terminal. Make sure you don’t connect the grid to the output terminal.
What to do if my InfiniSolar 10KW displays 'Solar input power abnormal'?
If your InfiniSolar Inverter displays 'Solar input power abnormal', it could be due to a damaged solar input driver or excessive solar input power when the voltage exceeds 850V. Check if the solar input voltage is higher than 850V. If not, contact your installer.
Defines warning and caution terminology used throughout the manual.
Lists essential safety guidelines and warnings for installation and use.
Lists all components included in the inverter package.
Identifies and illustrates the external ports and components of the inverter.
Criteria for choosing a suitable and safe installation site.
Steps and requirements for physically mounting the inverter.
Specifies the correct cable requirements for grid connection.
Detailed steps for making the AC utility connection.
Guides on preparing cables and connectors for PV module wiring.
Process for connecting PV modules, including polarity and safety checks.
Specifies the correct cable requirements for AC output connection.
Detailed steps for making the AC output connection to the load.
Defines the pin layout and functions of the dry contact interface.
Recommended external circuit wiring for the dry contact.
Explains the behavior of the dry contact based on system status.
Identifies the active pins and connection method for the relay port.
Describes the output voltage from the relay port in different states.
Illustrates a circuit diagram for the relay control port application.
Explanation of available modes: Grid-tie, Off-Grid, and Grid-tie with backup.
Overview of the inverter's interface, buttons, and their functions.
Explains LCD information and how to navigate the query menu.
LCD display examples for different inverter operation modes.
Guidelines for ensuring the inverter operates correctly.
Safety measures and steps for servicing the battery system.
Lists common warning events, their icons, and descriptions.
Details fault codes, their possible causes, and solutions.
General| Power Output | 10kW |
|---|---|
| Rated Power | 10kW |
| Output Power | 10kW |
| Battery Voltage | 48VDC |
| Output Voltage | 220VAC/230VAC/240VAC |
| Output Frequency | 50Hz/60Hz |
| Protection | Over Temperature |
| Humidity | 5% to 95% (non-condensing) |
To Next Page
