To Next Page
C
castrobryanAug 16, 2025
How to fix InfiRay Thermal camera that can not be started?
- MmccalllaurenAug 16, 2025
If your InfiRay Thermal camera won't start, the battery is likely out of charge. Charge the battery.
How to fix InfiRay Thermal camera that can not be started?
If your InfiRay Thermal camera won't start, the battery is likely out of charge. Charge the battery.
What to do if InfiRay Thermal camera images are blurry but icons are clear?
If the icons on your InfiRay Thermal camera are clear but the images are blurry, it could be due to a couple of reasons: * The lens may not be focused correctly. Try rotating the lens focus ring to adjust the focus. * The lens's inner or outer optical surface might be dusty or iced. Wipe the outer optical surface with a soft cotton cloth, or leave the scope to dry in a warm, dry environment for more than 4 hours.
Why are my InfiRay Thermal camera images too dark?
If the images from your InfiRay Thermal camera are too dark, the display might not be bright enough. Adjust the display brightness to resolve this issue.
What to do if the position of the reticle moves after shooting with InfiRay Thermal cameras?
If the reticle position moves after shooting with your InfiRay Thermal camera, it might be because the scope or the fixing clamp isn't installed firmly. Check that the scope is installed firmly. Also, ensure that the bullet type and caliber match what you used for zeroing. Keep in mind that if you zeroed in summer but are using the scope in winter (or vice versa), the zeroing point may shift slightly.
What to do if InfiRay Thermal camera images are unclear, have vertical lines, or the background is uneven?
If your InfiRay Thermal camera images are unclear, show vertical lines, or have an uneven background, it indicates that calibration is required. Calibrate the images as instructed in Section 9 of the user manual.
What to do if my InfiRay Thermal camera cannot be powered by using an external power supply?
If your InfiRay Thermal camera won't power on with an external power supply, there could be a couple of reasons: * The USB cable might be damaged. Replace the USB cable. * The external power supply may not be providing enough power. Check the external power supply.
What to do if the image is too dark on InfiRay Binoculars?
If the image on your InfiRay Binoculars appears too dark, the most likely cause is that the screen brightness is set too low. To resolve this, simply adjust the brightness of the screen until the image is clear and well-lit.
Why won't my InfiRay Binoculars connect to my phone?
If you are unable to connect your InfiRay Binoculars with your smartphone or tablet PC, there are two primary reasons: 1. **Incorrect Wi-Fi password:** Ensure that you are entering the correct password for the Wi-Fi network. 2. **Too many Wi-Fi signals:** Move to an area with fewer Wi-Fi signals to reduce interference.
What to do if InfiRay Binoculars won't charge?
If you can't charge your InfiRay Binoculars using an external power supply, here are a couple of potential reasons: 1. **USB Cable:** The USB cable might be damaged. Try replacing it with a new one. 2. **External Power Supply:** The external power supply itself might be out of battery. Check the power supply to ensure it is working correctly.
Why does the Wi-Fi signal keep disappearing on my InfiRay Binoculars?
If the Wi-Fi signal to your InfiRay Binoculars is disappearing or being interrupted, it could be due to the device being out of range or obstructions such as concrete walls. Try repositioning the device to ensure a stable Wi-Fi signal.
General| Pixel Size | 12 μm |
|---|---|
| Frame Rate | 50 Hz |
| Waterproof Rating | IP67 |
| Video Recording | Yes |
| Photo Capture | Yes |
| Wi-Fi | Yes |
| Stadiametric Rangefinder | Yes |
| Detector Resolution | 384x288 |
| Battery Type | Built-in Li-ion battery |
| Diopter Adjustment | -5 to +5 |
| Operating Temperature | -20 °C~+50 °C |
| Battery Life | ≥6 h |
| Focus Range | 1 m ~ ∞ |
