Why won't my InfiRay Tube TL35 SE connect to my phone or computer?
There might be a few reasons why your device isn't connecting. First, double-check that you've entered the correct Wi-Fi password. Also, too many Wi-Fi networks in the area can cause interference. Try moving to a location with fewer networks or no Wi-Fi coverage to establish a stable connection.
What to do if the image on my InfiRay Tube TL35 SE is too dark?
If the image appears too dark, the screen brightness might be set too low. Try adjusting the display brightness to see if that improves the image visibility.
How to fix blurry image on InfiRay Thermal cameras, but the icons are clear?
If your icons are clear but the image is blurry, it could be due to a focusing issue or the lens condition. Here's what you can do: * Rotate the lens focus ring to adjust the focus. * Inspect the lens for dust or ice. If present, gently wipe the outer optical surface with a soft cotton cloth, or allow the scope to dry in a warm, dry environment for at least 4 hours.
What to do if Wi-Fi signals are lost on InfiRay Thermal cameras?
If you're experiencing Wi-Fi signal loss or interruption, it could be because the device is out of Wi-Fi range or there's an obstruction, like a concrete wall, blocking the signal. Try moving to a location where you can receive Wi-Fi signals clearly.
Why does the reticle position move after shooting with InfiRay Tube TL35 SE Thermal cameras?
If the reticle position shifts after shooting, the scope or clamp might not be securely mounted. Check that the scope is firmly attached. Also, ensure the bullet type and caliber match what was used during zeroing. Keep in mind that zeroing may slightly change between seasons (summer to winter or vice versa).
What to do if my InfiRay Tube TL35 SE Thermal cameras won't start?
If the scope won't start, the battery is likely out of charge. Charge the device.
What to do if my InfiRay Thermal cameras observed target disappears?
If the observed target disappears, it might be because you are observing the target through glass. Observe the target directly without the presence of glass.
What to do if my InfiRay Thermal cameras won't power on with an external power supply?
If the device isn't powering on with an external power supply, the USB cable may be damaged; replace it. Also, the external power supply may be insufficient; check it if necessary.
General| Resolution | 384x288 |
|---|---|
| Frame Rate | 50 Hz |
| Lens | 35mm |
| Field of View | 7.5° x 5.7° |
| Pixel Size | 12 μm |
| Eye Relief | 50 mm |
| Display Resolution | 1024x768 |
| Display Type | OLED |
| Battery Type | Li-ion |
| IP Rating | IP67 |
| Spectral Range | 8-14 μm |
| Focus | Manual |
| Display Size | 0.39 inch |
| Dimensions | 385x85x75 mm |
| NETD | <50 mK |
| Digital Zoom | 2x, 4x |
| Thermal Sensitivity | <50 mK |
| Operating Temperature | -20°C to +50°C |
| Storage Temperature | -40°C to +60°C |
Safety regarding environmental factors, temperature extremes, and proper handling.
Explanation of the primary controller and power button functions.
Comprehensive guide on using the power button for various operations.
How to use the Controller and zoom handwheel for different functions.
Step-by-step charging guide and how to interpret indicators.
Key safety guidelines to follow during battery charging.
Instructions for physically attaching the scope to a weapon.
Steps for device startup and completing initial configuration.
Overview of the freezing zeroing method and initial steps.
Steps for aiming, noting impact, and adjusting the reticle.
Explanation of calibration modes and how to perform them.
Explanation of continuous vs. single ranging and their controls.
Quick access to common settings like video recording and reticle options.
Choosing and confirming zeroing profiles and distances.
Selecting zeroing distances and entering the zeroing interface.
Adjusting the reticle to impact point using image freezing.
Process for setting custom zeroing distances.
Why and how to calibrate the laser rangefinder.
Procedure for resetting the device to its original configuration.
How to connect the scope to smartphones/laptops via Wi-Fi.
Solutions for device not starting or unclear images.
How to fix dark images or focus issues.
Solutions for reticle movement and focusing failures.
Addressing issues with Wi-Fi connection and signal loss.
To Next Page
