Ingersoll-Rand Man Rider LS2-150HLP Series User Manual

12 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

Review Proof Only 9/2/09

Product

Maintenance

Information

Hydraulic Man Rider™ Winch

LS2-150HLP Series

Models

(Dwg. MHP2876)

Save These Instructions

LS2-150HLP-L()-E

(Lever Control)

LS2-150HLP-PHXXM-()-E

(Remote Control)

Form MHD56364

Edition 1

June 2009

43802123

© 2009 Ingersoll-Rand Company

Table of Contents

Questions and Answers:

J
Jimmy RyanAug 12, 2025
How to troubleshoot Ingersoll-Rand Winches that will not operate?
- M
  Michelle FrankAug 12, 2025
  If your Ingersoll-Rand Winch isn't operating, several factors could be the cause. First, ensure there's sufficient oil supply pressure and volume at the winch inlet, and clean the oil filter. Check that the winch isn't overloaded beyond its rated capacity. Verify that the disc brake releases by pressurizing the disc brake release port and checking for excessive leakage from the case drain port. Also, confirm that shipping plugs have been removed from valve and motor ports. The motor itself might be damaged, requiring disassembly and cleaning. Lastly, check that the system relief valves are set correctly.
A
Adam JacobsAug 16, 2025
What to do if Ingersoll-Rand Man Rider LS2-150HLP run slow?
- H
  Harold SmithAug 17, 2025
  If your Ingersoll-Rand Winch is running slower than expected, here are some potential causes and solutions: * Check for improper hose or fitting sizes that may be restricting oil flow. Inspect and, if necessary, replace any parts causing restriction, and check the oil filter. * The motor may be damaged, requiring removal, disassembly, and inspection for worn or damaged parts. * Ensure the brakes are releasing properly. * Verify sufficient oil supply pressure and volume at the winch inlet, and clean the oil filter. * If the hydraulic oil is cold, run the hydraulic pump to warm and circulate the oil through the system.
M
Meagan BurchAug 20, 2025
Why does the load continue to move when Ingersoll-Rand Man Rider LS2-150HLP Winches are stopped?
- J
  jenniferburnsAug 20, 2025
  If the load continues to move after your Ingersoll-Rand Winch has stopped, it could be due to several reasons. The brake might be slipping, so check the brake friction disc wear. Another possibility is that the winch is overloaded, so reduce the load to within its rated capacity. Also, the control valve may not be the correct type; it should have all ports open to the reservoir when the spool is in the neutral position. Finally, there could be excessive back pressure acting on the reverse port of the winch motor and disc brake charge port; install pressure gauges in motor lines to check this.
A
Andrew VazquezAug 25, 2025
Why Ingersoll-Rand Man Rider LS2-150HLP motor does not run smoothly?
- D
  Drew LittleAug 26, 2025
  If the motor on your Ingersoll-Rand Winch isn't running smoothly, is running hot, or is making excessive noise, it could be due to air entering the hydraulic system; check the hoses and hose connections. It could also be due to using the incorrect oil type; replace the oil with the type recommended.
J
johnrosalesAug 29, 2025
How to fix a control valve lever that is hard to actuate on Ingersoll-Rand Winches?
- D
  dsalazarAug 29, 2025
  If the control valve lever on your Ingersoll-Rand Winch is hard to actuate or doesn't spring return to neutral, it could be due to the valve spool sticking. Remove and disassemble the control valve, then repair it.
C
Christine MeltonSep 2, 2025
What to do if there is an oil leak from the motor end of Ingersoll-Rand Winches?
- M
  Michael BennettSep 2, 2025
  If you notice an oil leak from the motor end of your Ingersoll-Rand Winch, it could be that the reduction assembly is leaking. To address this, disassemble the winch and inspect the reduction assembly seals.

Ingersoll-Rand Man Rider LS2-150HLP Series Specifications

General

Model	LS2-150HLP Series
Manufacturer	Ingersoll-Rand
Category	Winches
Capacity	1500 kg
Mounting	Base Mounted
Control	Pendant Control
Safety Features	Emergency Stop, Overload Protection

Related product manuals

Preview: FORCE 5i Man Rider FA150KGi

FORCE 5i Man Rider FA150KGi

Preview: Rider MR150K Series

Rider MR150K Series

Ingersoll-Rand FA7

Ingersoll-Rand FA2i

Ingersoll-Rand LS2000R

Ingersoll-Rand Force 5

Ingersoll-Rand LS1500R

Ingersoll-Rand PS2400RGC

Preview: Ingersoll-Rand force 5 FA5

Ingersoll-Rand force 5 FA5

Preview: Ingersoll-Rand FA2.5A Series

Ingersoll-Rand FA2.5A Series

Preview: Ingersoll-Rand LIFTSTAR Series

Ingersoll-Rand LIFTSTAR Series

Ingersoll-Rand FA150KGi Series