Inovance IS620PT012I - User Manual

109 pages

Save Page as PDF

To Next Page

To Next Page

Loading...

Table of Contents

Questions and Answers

K
kfreemanAug 18, 2025
What to do if the LED display is not on for Inovance Controller?
- T
  Thomas PetersonAug 18, 2025
  If the LED display of your Inovance Controller is not on or doesn't show "rdy", it could be due to several reasons. First, the control power voltage might be abnormal, so measure the AC voltage between L1C and L2C. Second, the main power voltage might be abnormal; for a single-phase 220 V model, measure the AC voltage between L1 and L2. If the DC bus voltage amplitude (voltage between P and -) is lower than 200 V, "nrd" will be displayed. Third, the program burning terminal might be shorted, so check it. Finally, the servo drive itself might be faulty.
K
Kristina LopezAug 20, 2025
Why is the shaft of my Inovance Controller's servo motor in free running status?
- W
  williamsbenjaminAug 21, 2025
  If the shaft of your servo motor is in a free running status, ensure the S-ON signal is valid by setting the operation panel to servo status display and checking if it displays "rdy" instead of "run". Also, verify that the control mode selection is correct by checking if H02-00 is set to 1.
J
Joseph HillAug 23, 2025
Why doesn't the servo motor rotate in my Inovance Controller?
- A
  Alice FischerAug 23, 2025
  If your Inovance Controller's servo motor does not rotate, it could be due to an internal torque reference (H0B-02) being 0. Check whether the polarity of the input signal is reversed.
W
William OneillAug 26, 2025
Why is my Inovance Controller's servo motor rotating in the reverse direction?
- J
  Joseph LopezAug 26, 2025
  If the servo motor of your Inovance Controller rotates in the reverse direction, and you're using AI to input torque reference, check whether the polarity of the external voltage input signal is reversed, as the internal torque reference (H0B-02) might be negative.
P
perezalexAug 28, 2025
What causes the servo motor of Inovance Controller to not rotate or have abnormal speed?
- K
  Kenneth GuzmanAug 28, 2025
  If the servo motor does not rotate or the motor speed is abnormal, it might be caused by incorrect AI wiring. Verify that the analog input channel is selected correctly and that the selected AI terminal is wired correctly.
S
salinasfranciscoAug 30, 2025
How to fix unsteady motor speed on Inovance Controller?
- B
  Brian JacksonAug 30, 2025
  If the motor speed of your Inovance Controller is not steady, perform automatic gain tuning, as the gain might be set improperly.
T
Traci OlsonSep 1, 2025
What causes the motor shaft to vibrate left and right on Inovance Controller?
- B
  billy68Sep 1, 2025
  If the motor shaft vibrates left and right, it might be because the load inertia ratio (H08-15) is too large. Perform inertia auto-tuning and automatic gain tuning on your Inovance Controller.
D
Douglas WelchSep 3, 2025
What to do if the servo motor of Inovance Controller does not rotate?
- J
  jnewtonSep 3, 2025
  If your Inovance Controller's servo motor does not rotate, it could be due to the input reference pulse counter (H0B-13) being 0. Check whether the high/low-speed pulse input terminal is wired correctly. Alternatively, it could be that the position reference is not input. Check whether FunIN.13: INHIBIT (pulse input forbidden) or FunIN.37: PulseInhibit (pulse forbidden) is used.
P
Patrick MccallSep 6, 2025
Why does my Inovance Controller's servo motor jitter at low speed?
- C
  Caitlin WatkinsSep 6, 2025
  If your Inovance Controller's servo motor jitters at low speed, it might be because the motor speed is not steady. The gain may be set improperly.
S
stephenriveraSep 8, 2025
What to do if Inovance Controller's servo drive is faulty?
- D
  David CampbellSep 8, 2025
  Replace the servo drive.

Inovance IS620PT012I Specifications

General

Series	IS620P
Rated Output Current	12A
Control Mode	Position, Speed, Torque
Communication Interface	RS485, CANopen
Protection Level	IP20
Rated Current	12A
Output Current	12A
Feedback	Incremental Encoder

Related product manuals

Inovance IS620PT017I

Inovance IS620PT021I

Inovance IS620PT026I

Inovance IS620PT3R5I

Inovance IS620PT5R4I

Inovance IS620PT8R4I

Inovance IS620PS1R6I

Inovance IS620PS2R8I

Inovance IS620PS5R5I

Preview: Inovance IS620P Series

Inovance IS620P Series

Inovance IS650PT032IUX-B

Inovance IS650PT037IUX Series