What does user-defined fault 2 mean for Inovance MD380S0.4GB?
If your Inovance DC Drive reports a 'User-defined fault 2', it means the user-defined fault 2 signal is being input via DI or virtual I/O. To resolve this, reset the operation.
Why does Inovance MD380S0.4GB DC Drives have overcurrent during acceleration?
When an Inovance DC drive experiences overcurrent during acceleration, it may be due to a grounded or short-circuited output circuit, failure to perform motor auto-tuning, an excessively short acceleration time, an inappropriate manual torque boost or V/F curve, low voltage, starting a rotating motor, a sudden load during acceleration, or an undersized AC drive. To address this, eliminate external faults, perform motor auto-tuning, increase the acceleration time, adjust the manual torque boost or V/F curve, correct the voltage, use rotational speed tracking restart or wait for the motor to stop before starting, remove the added load, or select an AC drive with a higher power class.
What to do if Inovance MD380S0.4GB show overcurrent at constant speed?
If you observe overcurrent at constant speed in Inovance DC Drives, it could be caused by a grounded or short-circuited output circuit, failure to perform motor auto-tuning, low voltage, a sudden load during operation, or an AC drive model with insufficient power. To fix this, eliminate any external faults, perform motor auto-tuning, ensure the voltage is within the normal range, remove any added loads, or choose an AC drive with a higher power class.
Why does Inovance DC Drives have overvoltage during deceleration?
If overvoltage occurs during deceleration in Inovance DC Drives, it could be due to high input voltage, an external force driving the motor, a deceleration time that is too short, or the absence of a braking unit and resistor. To solve this, adjust the voltage to the normal range, eliminate the external force or install a braking resistor, increase the deceleration time, or install the braking unit and braking resistor.
What does accumulative power-on time reached mean for Inovance MD380S0.4GB?
If your Inovance DC Drive indicates that the 'Accumulative power-on time reached', it signifies that the preset power-on time has been reached. Clear the record by using the parameter initialization function.
What causes initial position fault in Inovance DC Drives?
If your Inovance DC Drive shows an initial position fault, it means the motor parameters are not set based on the actual situation. Check that the motor parameters are set correctly and verify that the setting of rated current is not too small.
What does AC drive hardware fault mean in Inovance DC Drives?
If your Inovance DC Drive displays an 'AC drive hardware fault', it indicates either an overvoltage or overcurrent condition. Address the issue based on the specific overvoltage or overcurrent troubleshooting steps.
What causes pulse-by-pulse current limit fault in Inovance MD380S0.4GB?
If your Inovance DC Drive is experiencing a pulse-by-pulse current limit fault, it could be due to an excessively heavy load, a locked rotor on the motor, or an AC drive model with insufficient power. To fix this, reduce the load and check the motor and mechanical condition, or select an AC drive of higher power class.
What causes EEPROM read- write fault in Inovance MD380S0.4GB?
If your Inovance DC Drive displays an EEPROM read-write fault, it indicates that the EEPROM chip is damaged. Replace the main control board to resolve this.
What causes power input phase loss in Inovance MD380S0.4GB?
If your Inovance DC Drives show power input phase loss, it could be due to an abnormal three-phase power input, a faulty drive board, a faulty lightening board, or a faulty main control board. To address this, eliminate external faults or contact Inovance or their agent.
Detailed safety precautions for installation, wiring, operation, and maintenance.
General safety guidelines including RCD requirements, motor insulation, and thermal protection.
Guidelines for installing the MD380 AC drive, including environmental and clearance requirements.
Instructions for electrical installation, covering main and control circuit terminals and wiring.
Detailed description of the MD380 operation panel, including indicators, keys, and digital display.
Procedure for navigating and modifying function codes using the three-level menu structure.
Methods for starting and stopping the AC drive, including command source selection.
Configuration of main and auxiliary frequency sources, including digital, analog, and communication inputs.
Procedures for setting motor parameters and performing auto-tuning for optimal performance.
Recommendations for selecting peripheral EMC devices like input filters and reactors for optimal performance.
Methods to address current leakage issues, including circuit breaker selection and carrier frequency reduction.
Practical solutions for common EMC interference types like leakage, AC drive, communication, and I/O interference.
Table of electrical specifications for MD380 models, including power capacity, current ratings, and adaptable motor data.
Detailed physical appearance and mounting dimensions for MD380 AC drives in various housing types.
Procedures for routine maintenance and periodic inspection of the MD380 AC drive to ensure optimal performance and longevity.
Comprehensive guide to identifying and resolving common faults and errors encountered with the MD380 AC drive.
Troubleshooting common operational symptoms and diagnostic procedures for the MD380 AC drive.
To Next Page
General