Inovonics EN4204/R User Manual

C
EN4204/R EchoStream
®
Receiver
Installation Instructions - 05617B
1 Overview
The EN4204/R receiver allows you to add up to four transmitters to any
application. With diversity reception and advanced signal processing,
Inovonics Wireless EchoStream technology is designed to minimize dead
spots in transmission areas.
1.1 Inovonics Wireless Contact Information
If you have any problems with this procedure, contact Inovonics Wireless
technical services:
• E-mail: support@inovonics.com
• Phone: (800) 782-2709; (303) 939-9336
1.2 EN4204/R LEDs and Buttons
Figure 1 Receiver LEDs and Buttons
E
H
I
F
B
G
A
D
A Alarm LED B Tamper Fault LED C Low Battery Fault LED
D Inactive Fault LED E Power LED F Transmitter Number LEDs
G Advance Button H Decode LED I Reset Button
Most of the LEDs and buttons perform different function depending on
which mode the the EN4204/R is in.
Normal Operation Mode
Alarm LED: Lights when any transmitter is sending an alarm transmission.
Tamper Fault LED: Lights when any transmitter is sending a tamper
transmission.
Low Battery Fault LED: Lit when any transmitter has a low battery.
Inactive Fault LED: Lit when any transmitter is inactive.
Power LED: Lit when receiving power.
Transmitter Number LEDs: Lit when the transmitter is in alarm.
Advance Button: Press the Advance button to enter status review mode.
Decode LED: Flashes when any recognizable transmission is received.
This LED is only visible when the pry-out door or cover is removed.
Reset Button: Clears the current status for all points and resets all outputs
and LEDs. Resets the supervision window timers. This button is only
accessible when the pry-out door or cover is removed.
Status Review Mode
Alarm LED: Lights when the selected transmitter is sending an alarm
transmission.
Tamper Fault LED: Lights when the selected transmitter is sending a
tamper transmission.
Low Battery Fault LED: Lit when the selected transmitter has a low
battery.
Inactive Fault LED: Lit when the selected transmitter is inactive.
Power LED: Lit when receiving power.
Transmitter Number LEDs: Shows status of the transmitter assigned to
that number when lit. Use the advance button to scroll through transmitters.
Advance Button: Scrolls through transmitters to display status.
Decode LED: Flashes when any recognizable transmission is received.
This LED is only visible when the pry-out door or cover is removed.
Reset Button: Clears the current status for all points and resets all outputs
and LEDs. Resets the supervision window timers. This button is only
accessible when the pry-out door or cover is removed.
1.3 EN4204 Internal Components
A
B
C
D
I
J
H
L
E
A
G
F
K
M
A
Figure 2 EN4204 Components
A Housing release
tabs
B Power (11-14
VDC)
C Ground connection
D Output terminals E Fault output F Advance button
G Reset button H Reset input I Jam output
J Tamper output K Program button L Frequency band selection
pins
M Decode LED
1.4 EN4204R Internal Components
A
B
C
D
I
J
H
L
E
A
A
M
F
K
G
Figure 3 EN4204R Components
A Housing release
tabs
B Power (11-14
VDC)
C GND connection
D Output terminals E Fault output F Advance button
G Reset button H Reset input I Jam output
J Tamper output K Program button L Frequency band selection
pins
M Decode LED
2 Installation and Startup
2.1 Connect Power Cabling
Before beginning startup, you will have to connect power to the receiver. To
connect power to the receiver:
1. Use a small screwdriver to press the housing release tab on the top or
bottom of the receiver; separate the housing.
2. Connect power cabling to the Power and GND connections.
• Power source should be 11-14 VDC. Power supply must be
unswitched, uninterrupted, and regulated.
© Inovonics, 2009 - www.inovonics.com
Available from A1 Security Cameras
www.a1securitycameras.com email: sales@a1securitycameras.com

Inovonics EN4204/R Specifications

Summary

Overview

Inovonics Wireless Contact Information

Contact details for Inovonics Wireless technical services, including email and phone numbers for support.

EN4204/R LEDs and Buttons

Description of the LEDs and buttons on the EN4204/R receiver and their functions in normal and status review modes.

EN4204 Internal Components

Diagram identifying the internal components of the EN4204 receiver.

EN4204R Internal Components

Diagram identifying the internal components of the EN4204R receiver.

Installation and Startup

Connect Power Cabling

Instructions for connecting the power supply to the EN4204/R receiver.

Select the Frequency Band

Guide on configuring the receiver's radio frequency band based on geographic location.

Program the Receiver

Steps for programming transmitter points, supervision windows, and output types.

Factory Config

Procedure to restore the EN4204 receiver to its default factory settings.

Receiver Terminals and Connections

Mount the Receiver

Instructions for physically mounting the receiver, including placement considerations.

Specifications

Technical specifications for the EN4204/R receiver, including dimensions and operating environment.

Warranty and Disclaimer