What to do if my Insignia NS-AF50MBK9-C is not working?
If your Insignia fryer isn't working, make sure that the power cord is plugged into a grounded wall outlet. Also, check that you have set the timer. Turn the timer knob to the required preparation time to turn on the fryer. Finally, ensure that the pan is properly placed into the fryer by sliding it in correctly.
Why is white smoke coming out of my Insignia NS-AF50MBK9-C Fryer?
If you notice white smoke coming from your Insignia air fryer, it's likely due to preparing greasy foods, which causes a large amount of oil to leak into the pan. This oil produces white smoke, and the pan may heat up more than usual. Also, white smoke can appear if the pan still has grease residue from a previous use. Ensure you clean the pan properly after each use to prevent this.
Why is the food fried in my Insignia NS-AF50MBK9-C Fryer not done?
If the food fried in your Insignia air fryer isn’t fully cooked, it might be due to several reasons. First, there may be too much food in the air fryer. Try cooking smaller batches for more even frying. Second, the temperature might be too low, so increase the air fryer’s temperature. Finally, the preparation time may be too short, so cook your food longer.
What to do if I cannot slide the pan into my Insignia NS-AF50MBK9-C Fryer properly?
If you cannot slide the pan into your Insignia fryer properly, it could be because there is too much food in the basket. Make sure you do not fill the basket beyond the MAX indication. Also, ensure that the basket is placed correctly in the pan. Push the basket down into the pan until you hear a click.
Why are the ingredients fried unevenly in my Insignia Fryer?
If ingredients are fried unevenly in your Insignia air fryer, it may be because certain foods need to be shaken during cooking. For foods that lie on top of each other, such as fries, shake them halfway through the preparation time to ensure even cooking.
Why are my fresh fries fried unevenly in my Insignia Fryer?
Unevenly fried fresh fries in your Insignia air fryer can result from not using the right type of potato. Use fresh potatoes to ensure they stay firm during frying. Also, make sure to rinse the fries properly before frying to remove starch from the outside.
Why are my fried snacks not crispy in my Insignia NS-AF50MBK9-C Fryer?
If your fried snacks aren't crispy when they come out of the Insignia air fryer, it could be because you used snacks meant for a traditional deep fryer. Try using oven snacks or lightly brush some oil onto the snacks for a crispier result.
Why are my fresh fries not crispy when they come out of the Insignia Fryer?
If your fresh fries aren't crispy after using the Insignia fryer, remember that the crispiness depends on the amount of oil and water in the fries. Ensure you dry the potato sticks properly before adding oil. You can also cut the potato sticks smaller or add slightly more oil for a crispier result.
Read all provided instructions before operating or cleaning the appliance.
Use handles or knobs; use oven mitts or potholders to avoid burns from hot surfaces.
Do not immerse cord, plugs, or appliance in water or other liquid.
Appliance not for use by persons with reduced capabilities unless supervised.
Children must be supervised to ensure they do not play with the appliance.
Unplug when not in use and before cleaning; allow to cool down.
Do not operate with damaged cord/plug; seek qualified repair for malfunctions.
Use only manufacturer-recommended accessory attachments to prevent injury.
Do not use the appliance outdoors.
Keep cord from hanging over edges or touching hot surfaces.
Avoid placing near heat sources or in heated ovens.
Use extreme caution when moving an appliance containing hot oil or liquids.
Disconnect by turning dials to OFF and removing the plug from the outlet.
Use appliance only for its intended purpose.
Ensure frying basket drawer is locked into the front of the fryer.
Ensure basket drawer is fully closed and locked during operation.
All users must read and understand the manual before operating or cleaning.
Use only a 120V AC electrical outlet for the power cord.
Unplug immediately if malfunction occurs; do not attempt repair.
To Next Page
General