Insignia NS-RGFESS1 - User Manual

Questions and Answers:

W
wstephensAug 21, 2025
Why is my Insignia NS-RGFESS1 oven smoking excessively when broiling?
- L
  Linda WilsonAug 22, 2025
  Excessive smoke during broiling in your Insignia Ranges oven can be due to several reasons: the control may not be set correctly, the meat may be too close to the element, the meat might not be correctly prepared (remove excess fat), or grease has built up on oven surfaces. Regular cleaning is necessary when broiling frequently. Reposition the rack to provide the correct clearance between the meat and the element. Preheat the broil element for searing.
A
Anne ThompsonSep 4, 2025
Why does my Insignia Ranges drawer not slide smoothly or drags?
- K
  Kristen DuranSep 4, 2025
  The drawer of your Insignia Ranges might not slide smoothly or drags because it is out of alignment. Fully extend the drawer and push it all the way in. Also, the drawer may be overloaded or the load is unbalanced. Reduce weight and redistribute drawer contents.
M
Mary LivingstonSep 2, 2025
What to do if my Insignia Ranges cooktop has brown streaks or specks?
- M
  Mrs. Melissa AllenSep 2, 2025
  If your Insignia Ranges cooktop has brown streaks or specks, it means boilovers have been cooked onto the surface. Wait until the surface cools down, then use a scraper to remove those impurities. Use a blade scraper to remove soil.
D
Daniel ReyesSep 1, 2025
What to do if my Insignia NS-RGFESS1 Ranges control panel operates but the surface heating elements and the oven don't turn on?
- V
  Veronica StevensSep 1, 2025
  If the control panel of your Insignia Ranges operates but the surface heating elements and the oven don't turn on, your range is in demo mode. Press and hold the 1 and 9 number pads on the control panel simultaneously for three seconds, then release. Your range resumes its normal mode of operation.
T
tuckersusanAug 31, 2025
Why is my Insignia Ranges range not level?
- K
  Katherine MurphyAug 31, 2025
  Your Insignia Ranges may not be level because it has been installed incorrectly. Place an oven rack in the center of the oven, then place a level on the oven rack. Adjust the leveling legs at the base of your range until the oven rack is level. Make sure that the floor is level, strong, and stable enough to adequately support your range. If the floor is sagging or sloping, contact a carpenter to correct the situation. Also, the kitchen cabinets may not be correctly aligned, making your range appear not level, so make sure that the cabinets are square and provide sufficient room for installation.
D
Douglas WarrenAug 29, 2025
How to fix scratches or abrasions on the Insignia Ranges cooking surface?
- J
  James HopkinsAug 29, 2025
  Scratches on the cooking surface of your Insignia Ranges are not removable, but tiny scratches become less visible over time as a result of cleaning. Use a ceramic glass top cleaning cream. Do not use chemical or corrosive agents. To avoid scratches, use the recommended cleaning procedures. Make sure that cookware bottoms are clean before use, and use cookware with smooth bottoms.
K
Karen RobinsonAug 27, 2025
What to do if the display flashes on my Insignia NS-RGFESS1 Ranges?
- J
  jenningsrobertAug 28, 2025
  If the display flashes on your Insignia Ranges, it means there was a power failure. Reset the clock.
J
Jenna HurstAug 27, 2025
Why are my Insignia NS-RGFESS1 Ranges oven racks difficult to slide?
- E
  Eric DanielAug 27, 2025
  If the shiny, silver-colored racks were cleaned in a self-cleaning cycle, apply a small amount of vegetable oil to a paper towel and wipe the edges of the oven racks with the paper towel.
S
Stephanie HarperAug 25, 2025
What to do if my Insignia Ranges oven does not turn on?
- E
  Elizabeth SmallAug 25, 2025
  If your Insignia Ranges oven isn’t turning on, make sure that the electrical plug is inserted into a live, correctly grounded outlet. Also, a fuse in your home may be blown or the circuit breaker tripped, so replace the fuse or reset the circuit breaker. Ensure the oven controls have been set correctly. Also, the oven may be too hot, so let it cool. If a delayed start time has been set, press the Off/Clear pad to cancel it. Ensure the oven door closes correctly, and no items are obstructing it. Finally, your range may be in demo mode, so press and hold the 1 and 9 number pads on the control panel simultaneously for three seconds, then release.
S
Summer VazquezAug 23, 2025
Why are my Insignia NS-RGFESS1 surface burners not producing a rolling boil or cooking fast enough?
- W
  Wayne DiazAug 23, 2025
  The surface burners on your Insignia Ranges might not produce a rolling boil or cook fast enough if you are using inappropriate cookware, so use pans which are flat and match the diameter of the surface element you selected. Also, in some areas, the power (voltage) may be low, so cover the pan with a lid until the desired heat is obtained.