Interlogix ATS1197 User Manual

© 2019 UTC Fire & Security Americas Corporation, Inc. 1 / 14 P/N MAINST-ATS1197 (ML) • REV D • ISS 11JUN19
ATS1197 Smart Card Reader With Keypad
Installation Sheet
EN
DE
IT
1
2
EN: Installation Sheet
Mounting the unit
1. Remove power to the control panel, or 4-door DGP, as
applicable.
2. Remove the two front panel screws at the bottom of the
RAS (see Figure 1), and then remove the RAS back plate.
Retain the screws to secure the RAS later.
3. Position the RAS back plate (with the tamper spring at the
top) against the mounting surface to determine the
locations of mounting holes and for cabling access
(a reduced card reading range may occur if mounted on a
metal surface).
4. Mount the back plate on a flat surface using four screws
(the hole nearest the tamper spring must have a screw in
order for the tamper switch to work correctly).
5. Terminate the cable, as required (see wiring details
below).
6. For on-line mode, set the BUS address (DIP switches 1
through 4). For on-line mode, set the TERM switch (DIP
switch 5) as required. For off-line mode, the TERM switch
must be off (up). See DIP switch settings for details.
7. Mount the RAS on the back plate by engaging the top, and
then lowering the RAS to be flat against the back plate.
The rear tamper switch must be sealed for the system to
work correctly. Ensure that the back plate tamper spring
rests on the tamper switch actuator (protruding from the
resin in the back of the RAS) when the RAS is in position.
8. Fix the RAS to the back plate using the two screws
removed earlier from the bottom of the RAS.
9. Apply power to the control panel, or the 4-door DGP.
10. For online mode, use an LCD RAS on the BUS (or the
system management software) to program polling and set
up the required items for the new RAS. In particular, the
ATS1197 RAS must be programmed as a non-LCD RAS.
11. Check that the ATS1197 is communicating correctly and
verify that the tamper switch is working properly (i.e. "RAS
Tamper" is not showing on the LCD RAS).
WARNING: All power should be turned off to the control panel
before wiring the RAS.
Location of features
Figure 1 legend
(1) Red/Green dual colour LED
(2) Yellow LED
(3) Red LED
(4) Locking screws
Connecting control panel to keypad RAS
Refer to the ATS Control Panel Installation Guide for
instructions.
1 2 3
4 5 6
7 8 9
0 #
(4)
(1) (2) (3)
RAS 1
RAS 5
RAS 9
RAS 13
RAS 2
RAS 6
RAS 10
RAS 14
RAS 3
RAS 7
RAS 11
RAS 15
RAS 4
RAS 8
RAS 12
RAS 16
()2()1

Interlogix ATS1197 Specifications

General

Type	Proximity Card Reader
Frequency	125 kHz
Form Factor	Wall mount
Buzzer	Yes
Current Draw	100 mA max
LED Indicator	Yes

Summary

Installation Sheet

Mounting the Unit

Steps for physically installing the ATS1197 reader on a mounting surface.

Location of Features

Identifies key physical components of the ATS1197 reader as shown in Figure 1.

Connecting Control Panel to Keypad RAS

Instructions for connecting the ATS1197 reader to the control panel.

Tamper Switch and DIP Settings

Tamper Switch

Explains the function and behavior of the ATS1197 tamper switch.

RAS DIP Switch Settings

Details on configuring the RAS address and bus termination using DIP switches.

Connections Overview

Lists the wire colors and their corresponding applications and voltage requirements.

Status LED Indications

Explains the meaning of the LED lights on the ATS1197 reader.

Operating Features

Describes optional features like night light and beeper tone adjustment.

Power Up and Troubleshooting

Power Up Sequence

Describes the initial power-on sequence and memory check of the ATS1197.

General Faults Troubleshooting

Provides common troubleshooting steps for issues like no LED display or flashing LEDs.

Rx and Tx LED Indications

Explains the meaning of the Rx and Tx LEDs for diagnosing communication issues.

Configuring the ATS1197 RAS

Step-by-step guide to configure the reader's settings via the control panel menu.

Programming Map and Options

Overview of available programming options and how to access the menu.

Menu Configuration Options

Menu 2: LEDs Offline

Configuration options for LED control, including two-wire and one-wire modes.

Menu 3: Valid Card Flash

Setting for the green LED to flash upon a valid card read.

Menu 4: Night Light

Option to enable a dimly lit keypad backlight for locating the reader in darkness.

Menu 5: Protocol Options

Selects the data transmission protocol (Wiegand or Magnetic stripe).

Menu 6: Card Beep

Controls the audible beep feedback when a card is badged.

Menu 7: Watchdog

Enables a watchdog function to report connection status in offline mode.

Menu 8: O/C Output

Configures the open collector output for door relay, tamper, or card data.

Menu 9: Option Card

Enables or disables the use of reader configuration cards.

Menu 10: RTE (Egress)

Configures Request To Exit (RTE) control and door relay options.

Menu 11: Factory Defaults

Resets all RAS settings to their original factory default condition.

Menu 13: Last Card

Displays the number of the last card badged on the reader.

Menu 16: Security Mode

Selects the type of user card the reader will recognize (unsecured or secured).