EasyManuals Logo

Intex 128454GN Owner's Manual

Intex 128454GN
43 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #12 background imageLoading...
Page #12 background image
299
A
S AVE THESE INSTRUCTIONS
(299IO) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 08/20/2018
English
Page 11
SET UP (continued)
Inate the Spa Cover Air Bladder
1.
Opentheinationvalveandinserttheinationhose
(7)
intothevalve;presstoinateuntilitisrmtothe
touch but not hard
(see drawing 6)
.
2.
Disconnecttheinationhose
(7)
from the air blower
inationoutletandthevalve.
3.
Replacethecontrolbaseinationcap
(9)
back; close and
recesstheinationvalve.
NOTE:
If there is a need to add some air to the spa tub wall or
spacoverairbladderaftertheyhavebeensetup,refertoabove“InatetheSpaTubWall”and“Inatethe
Spa Cover Air Bladder” sections. The cover air bladder is preinstalled inside the spa cover. If it needs to be
reinstalled,placetheuninatedairbladderinsidethespacoverlipbeforeinatingthebladder.
4.
Press the button to turn on the control unit panel
buttonsrst.Pressthebuttontoinatethespatub
wallfor8to10minutesuntilitisrmtothetouchbutnot
hard
(see drawing 5)
.
IMPORTANT:
Donotoverinateorusehighpressureair
compressortoinate.
5.
Press the button again to turn it off.
6.
Replace the air valve cap back.
NOTE:
The cap is designed to be screwed on and off.
Never exert force as this could cause the complete
internalinationsystemofthevalvetocomeloose.See“SpaTubAirValveFastening”forvalve
maintenance.
40
C
40
C
40
C
6
7
40
C
5
Deation
For Spa Tub Wall:
1.
Unscrew the cap to reveal the stem, push the stem in
and turn 90 degree right to secure it in the down position
(see drawing 7)
.
2.
Oncethedeationiscompleted,pushthesteminand
turn90degreelefttoreturnittotheinationposition.
3.
Replace the cap back.
NOTE:
Todeatethespatubforstorage,see“STORAGE”
section.
For Cover Air Bladder:
1.
Pullvalvecapoutandsqueezethevalveatitsbaseuntildeated.
2.
Close and recess the valve back.
7
4
7
1 2
3
9
24
2.
Unscrewthecontrolbaseinationcap
(9)
torevealtheairblowerinationoutlet,insertoneendofthe
inationhose
(7)
into the outlet and turn to the right to lock it
(see drawing 3)
.
3.
Unscrewtheairvalvecaptorevealthestemintheuppositionforination.Inserttheotherendofthe
inationhose
(7)
into the valve and turn to the right to lock it in position
(see drawing 4)
.

Other manuals for Intex 128454GN

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Intex 128454GN and is the answer not in the manual?

Intex 128454GN Specifications

General IconGeneral
BrandIntex
Model128454GN
CategorySwimming Pool
LanguageEnglish

Related product manuals