What to do if my Intex 126368NP pump doesn't work?
If your Intex Swimming Pool pump isn't working, first ensure the pool is filled to the correct water level. Then, clean the strainer screens at the pool inlet. Also, tighten hose nuts and check the hose for damage to resolve any air leaks on the intake hose.
Why is my Intex Swimming Pool 6-way valve/cover leaking?
If your Intex Swimming Pool 6-way valve or cover is leaking, first remove the 6-way valve cover and ensure the o-ring is in place. If the o-ring is dirty, clean it with garden hose water. Also, check that the flange clamp is securely tightened.
How to fix a leaking hose on my Intex Swimming Pool?
To fix a leaking hose on your Intex Swimming Pool, start by tightening or reinstalling the hose nut. Also, ensure the o-ring or L-shape o-ring is in place at the hose connection fitting and is not damaged.
What to do if my Intex Swimming Pool filter motor fails to start?
If your Intex Swimming Pool filter motor isn't starting, first ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. Also, check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, there may be an electrical defect requiring an electrician. Finally, the motor might be too hot; let it cool down before restarting.
How to improve Intex 126368NP Swimming Pool filter if it doesn’t clean the pool?
If your Intex Swimming Pool filter isn't cleaning the pool effectively, make sure to adjust the chlorine and pH levels. Also, ensure the filter tank is loaded with filter sand. Set the valve to the 'FILTER' position and operate the filter for longer periods if the pool is excessively dirty. Clean the strainer screen at the inlet to ensure it isn't restricting water flow.
Why is sand flowing back into my Intex Swimming Pool?
If sand is flowing back into your Intex Swimming Pool, it could be due to the sand being too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Alternatively, the sand bed may be calcified, in which case you should change the sand.
What to do if my Intex 126368NP Swimming Pool inlet threaded air connector or air jet valve is leaking?
If your Intex Swimming Pool inlet threaded air connector or air jet valve is leaking, try the following: * Tighten or reinstall the plunger valve. * Tighten the air jet valve and make sure it’s facing up. * Turn the pump ON and run for a few seconds, then turn OFF; repeat this 3 times to clear a blocked air jet valve internal seal. * Remove the air jet valve, flush out any dirt with water, and replace the valve back.
What to do if the pressure gauge on my Intex 126368NP Swimming Pool doesn’t work?
If the pressure gauge on your Intex Swimming Pool isn’t working, clear any obstructions in the intake by unscrewing it from the 6-way valve.
Why is the timer inaccurate or can't be set on my Intex Swimming Pool?
If the timer is inaccurate or can't be set on your Intex Swimming Pool, turn off the pump and restart it 5 minutes later. Also, try re-setting the timer.
Why is there a small leak from the air jet valve on my Intex Swimming Pool when the pump is on?
If you notice a small leak from the air jet valve when the pump is on, it may be due to accessories attached to the water circulation line. Remove all accessories (such as solar mat, auto pool cleaner, LED light) from the water circulation line and place the air jet valve cap over the air jet valve. Do not cover the air jet valve with the valve cap under normal situations or when the pump is operating.
Provides crucial warnings about potential hazards associated with the product.
Instructions for assembling the pool outlet strainer and plunger valve.
Instructions for assembling the pool inlet nozzle and plunger valve.
Instructions for setting up the motor pre-filtering assembly.
Guidance on how to install the sand tank.
Instructions for loading the filter sand into the tank.
Steps for installing the 6-way valve onto the filter.
Instructions on how to install the cell housing.
Explains the 6-way valve positions and functions.
Details initial setup and operation procedures.
Operating modes for pump, chlorinator, and BOOST.
Ideal salt levels and procedure for adding salt.
Tables and formulas for salt, cyanuric acid, and operating times.
Cleaning the motor pre-filter and electrodes.
Using test strips and understanding chemical parameters.
Instructions for storing the pool for the off-season.
Common pool issues, troubleshooting, and general safety.
General| Brand | Intex |
|---|---|
| Model | 126368NP |
| Material | PVC |
| Shape | Round |
| Type | Swimming Pool |
| Capacity | 1, 018 gallons |
| Capacity (Gallons) | 1018 |
| Included Items | Pool, filter pump, ladder, ground cloth |
To Next Page