What to do if my Intex Swimming Pool pump doesn’t work?
If the pump isn’t working, first, ensure the pool is filled to the correct water level. Next, clean the strainer screens at the pool inlet. Also, check for air leaks on the intake hose by tightening hose nuts and inspecting the hose for damage. If these steps don’t resolve the issue, contact an Intex service center, as the motor may be faulty or the impeller may be jammed.
Why is my Intex ULTRA XTR 126364GN Swimming Pool 6-way valve/cover leaking?
If the 6-way valve or cover is leaking, first remove the 6-way valve cover and ensure the o-ring is in place. If the o-ring is dirty, clean it with garden hose water. Also, make sure the flange clamp is securely tightened. If the issue persists, the 6-way valve may be damaged, and you should contact an Intex service center.
What to do if Intex ULTRA XTR 126364GN filter motor fails to start?
If the filter motor fails to start, there are several possible causes. First, ensure the line cord is plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter, or RCD. If the GFCI/RCD circuit breaker has tripped, reset it. If it repeatedly trips, your electrical system may have a defect, so turn off the breaker and call an electrician. It's also possible the motor is too hot; in this case, let it cool down before restarting.
What to do if my Intex ULTRA XTR 126364GN filter doesn’t clean the pool?
If your filter isn’t cleaning the pool, consider these possible causes. Adjust the chlorine and pH levels, consulting your local swimming pool supply store for guidance. Ensure the tank is loaded with filter sand according to the sand loading instructions. Verify that the 6-way valve is set to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Also, clean the strainer screen at the inlet to prevent restricted water flow.
Why is sand flowing back into my Intex ULTRA XTR 126364GN?
If sand is flowing back into the pool, it could be due to the sand being too small. Use only No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Alternatively, the sand bed may be calcified, in which case you should change the sand.
How to fix a leak from the hose of my Intex ULTRA XTR 126364GN?
To address a leaking hose, first, try tightening or reinstalling the hose nut securely. If the leak persists, check for a missing or damaged o-ring/L-shape o-ring at the hose connection fitting and ensure it is in place.
Why is my Intex ULTRA XTR 126364GN timer inaccurate or can't be set?
If the timer is inaccurate or cannot be set, the inner timer might be defective. Try turning off the pump and restarting it 5 minutes later. If that doesn't work, reset the timer. If problems persist, contact Intex service center.
What to do if my Intex ULTRA XTR 126364GN inlet threaded air connector / air jet valve is leaking?
If the inlet threaded air connector or air jet valve is leaking, try tightening or reinstalling the plunger valve. Ensure the air jet valve is tight and facing up. If the internal seal is blocked, turn the pump on for a few seconds, then off, and repeat three times. If the seal is dirty, remove the air jet valve, flush out dirt with water, and replace the valve. If the valve is broken, replace it with a new one.
What to do about a small leak from the air jet valve when the Intex ULTRA XTR 126364GN Swimming Pool pump is on?
If there is a small leak from the air jet valve when the pump is on, remove all accessories (such as solar mat, auto pool cleaner, LED light) from the water circulation line and place the air jet valve cap over the air jet valve. Do not cover the air jet valve with the valve cap under normal situation or when the pump is operating.
What to do if the pressure gauge on my Intex ULTRA XTR 126364GN Swimming Pool doesn’t work?
If the pressure gauge isn’t working, first check for a clogged inlet by unscrewing it from the 6-way valve and clearing any obstructions. If the gauge is still not working, contact an Intex service center because the pressure gauge may be damaged.
Mandatory safety rules for installation and use, including supervision and electrical precautions.
List and diagram of all components for assembly and identification.
Details on certified model number, power, wattage, pressure, flow rate, and media quantity.
Install on solid base, protected location, allow air circulation, team assembly recommended.
Connect pre-filter housing to motor inlet. Replace basket and leaf trap cover.
Place tank on base, connect motor assembly, secure to ground if required.
Use specified sand/glass media. Load between MAX and MIN marks. Distribute evenly.
Connect 6-way valve to tank and pump hose. Ensure outlet faces pool, inlet faces motor.
Connect hoses to pre-filter and plunger valve. Direct drain hose properly. Ensure nuts are tight.
Details on FILTER, BACKWASH, RINSE, WASTE, RECIRCULATE, CLOSED positions and their functions.
Explanation of ON/OFF button, LOCK/UNLOCK button, TIMER button, and LED readings.
Initial startup, backwashing, rinsing, filtering, and timer mode operation.
How to operate continuously and view preset timer hours.
Table showing required pump operating time for various Intex pool sizes.
Table showing required pump operating time for various non-Intex pool sizes.
Steps to clean the basket, leaf trap cover, and housing. Inspect filter media regularly.
Maintaining water balance with sanitizers and proper chemical use. Consult pool professional.
Steps to drain, dry, and store the filter pump and components properly for winter.
Solutions for common filter pump problems like motor failure, poor cleaning, and leaks.
Addresses algae, colored water, cloudy water, and sediment issues with causes and solutions.
General safety rules for pool use, including supervision, CPR, and emergency procedures.
Details on warranty period, coverage, exclusions, and claim procedures.
Supervise children, use on level base, one person at a time, check hardware, remove when not in use.
List and identification of all ladder parts and their quantities for different models.
Instructions for assembling side A and side B legs, ensuring J-shaped legs point outward.
Attaching the top platform to the assembled side legs.
Installing the U-shaped top rail, ensuring nuts and bolts are tightened.
Regular checks of hardware, ensuring secure steps, and proper use.
Procedure for removing ladder steps for storage and winterizing instructions.
Guidelines for pool safety, supervision, and emergency preparedness.
Details on the 1-year warranty for the Intex Pool Ladder, coverage, and exclusions.
General| Brand | Intex |
|---|---|
| Model | ULTRA XTR 126364GN |
| Type | Above Ground |
| Shape | Rectangular |
| Dimensions | 32ft x 16ft x 52in |
| Water Capacity | 14, 364 gallons |
| Material | PVC |
| Frame Material | Steel |
| Included Accessories | Ladder, Ground Cloth, Pool Cover |
| Warranty | 2-year limited warranty on pool liner, frame and pump |
To Next Page