Intex Ultra Rondo XTR

Questions and Answers

T
Tracy WilliamsAug 16, 2025
What to do if the Intex Ultra Rondo XTR Swimming Pool filter motor fails to start?
- R
  Richard CabreraAug 17, 2025
  If the Intex Swimming Pool filter motor won't start, ensure it's properly plugged into a 3-wire outlet protected by a Class A Ground Fault Circuit Interrupter (GFCI) or RCD. Also, check if the GFCI/RCD circuit breaker has tripped and reset it. If it repeatedly trips, there may be an electrical defect requiring an electrician. If the motor is too hot, let it cool down before restarting.
J
Joshua HoAug 19, 2025
Why is the Intex Swimming Pool filter not pumping water or has very slow flow?
- R
  Rodney MaynardAug 19, 2025
  If your Intex Swimming Pool filter isn’t pumping water or the flow is very slow, start by clearing any obstructions in the intake hose by discharging it inside the pool wall. Check for air leaks on the intake line by tightening hose nuts and inspecting hoses for damage, also check pool water level. Clean the pre-filtering basket more often if the pool is excessively dirty. Backwash the filter if the sand media is clogged with dirt. Ensure the nozzle is at the upper position of the pool inlet and the strainer at the lower position of the pool outlet. Remove about 1” of sand if there's crusting or caking on the filtering sand surface. Remove any pool vacuuming device attached to the system line. Finally, ensure the inlet threaded air connector is connected to the pool inlet upper hole.
Z
zacharyandersonAug 22, 2025
Why doesn't my Intex Ultra Rondo XTR Swimming Pool filter clean the pool?
- K
  Kyle SandovalAug 22, 2025
  If the Intex Swimming Pool filter isn’t cleaning the pool, adjust the chlorine and pH levels. Ensure the filter tank is loaded with filter sand according to the “sand loading instructions”. Set the 6-way valve to the “FILTER” position. If the pool is excessively dirty, operate the filter for longer periods. Clean the strainer screen at the inlet if it's restricting water flow.
G
Gregory ChapmanAug 25, 2025
What to do if Intex Ultra Rondo XTR Swimming Pool pump doesn’t work?
- S
  Stacy HarrisAug 26, 2025
  If the Intex Swimming Pool pump isn’t working, ensure the pool is filled to the correct water level. Clean the strainer screens at the pool inlet. Tighten hose nuts and check the hose for damage to address any air leaks on the intake hose. For a faulty motor or jammed impeller, contact the Intex service center.
D
Donna HernandezAug 27, 2025
How to stop sand from flowing back into the Intex Ultra Rondo XTR Swimming Pool?
- R
  richardjohnsonAug 27, 2025
  If sand is flowing back into your Intex Swimming Pool, ensure you're using No. 20 silica sand with a particle size range of 0.45 to 0.85 mm (0.018 to 0.033 inches) and a Uniformity Coefficient less than 1.75. Also, change the sand if the sand bed is calcified.
H
hillashleyAug 30, 2025
What causes the 6-way valve/cover to leak on my Intex Ultra Rondo XTR Swimming Pool?
- T
  Tiffany GreenAug 30, 2025
  If the 6-way valve or cover is leaking on your Intex Swimming Pool, remove the 6-way valve cover and ensure the o-ring is in place. Clean the sand tank o-ring with garden hose water if it's dirty. Tighten the flange clamp securely. If the 6-way valve is damaged, contact the Intex service center.
B
brycetuckerSep 2, 2025
How to fix an Intex Ultra Rondo XTR Swimming Pool inlet threaded air connector/air jet valve leak?
- C
  Carmen KelleySep 2, 2025
  If the inlet threaded air connector or air jet valve is leaking on your Intex Swimming Pool, tighten or reinstall the plunger valve to ensure it is well-fitted. Tighten the air jet valve and make sure it’s facing up. If the air jet valve internal seal is blocked, turn the pump ON and run for a few seconds, then turn OFF, repeat 3 times. If the air jet valve internal seal is dirty, remove the air jet valve, flush dirt out with water, and replace the valve back. If the air jet valve is broken, replace it with a new one.
S
Suzanne WestSep 5, 2025
How do I fix a leaking hose on my Intex Ultra Rondo XTR Swimming Pool?
- J
  Jared MartinezSep 5, 2025
  If the hose is leaking on your Intex Swimming Pool, tighten or reinstall the hose nut securely. Ensure the o-ring or L-shape o-ring is in place at the hose connection fitting and not damaged.
H
Heather TaylorSep 7, 2025
What to do if the Intex Swimming Pool pressure gauge doesn't work?
- L
  Leslie BrooksSep 7, 2025
  If the pressure gauge on your Intex Swimming Pool doesn’t work, clear any obstructions in the intake by unscrewing it from the 6-way valve. If the pressure gauge is damaged, contact the Intex service center.
T
Terri BaileySep 9, 2025
Why is the timer on my Intex Ultra Rondo XTR Swimming Pool inaccurate or can't be set?
- V
  velazquezdanielSep 10, 2025
  If the timer is inaccurate or can't be set on your Intex Swimming Pool, turn off the pump and restart 5 minutes later. Reset the timer. If the issue persists, contact the Intex service center.