What to do if the display of my Intex Bathtubs doesn't work?
If your Intex Bathtubs's display isn't working or the spa control unit is unresponsive, first, ensure the spa is properly plugged in and switched on. Check that the control panel cable is firmly attached to the control base. Verify the power source and reset the GFCI/RCD. If the issue continues, contact Intex Service Center.
How to level pump connectors with spa connectors on Intex Hot Tub?
To level pump connectors with spa connectors on your Intex Hot Tub, elevate the pump with wood or another type of insulated material to bring the pump’s connectors level with the spa’s connectors. This is because PVC can change shape, which is normal.
Why does my Intex PureSpa SB-H10 Hot Tub have a strange shape?
Your Intex Hot Tub might have a strange shape due to expanded internal air pressure caused by strong sunshine. Avoid exposing the spa to direct sunlight for extended periods. Also, check the air pressure and release air if necessary, especially during very hot weather, to prevent damage to the tub.
Why does my Intex Hot Tub keep tripping the household circuit breaker?
Your Intex Hot Tub might be tripping the circuit breaker for a few reasons: * The circuit breaker may be under-rated. Ensure you have the correct circuit breaker rating. * The circuit breaker might be overloaded. Provide a dedicated circuit breaker feeding the spa electrical outlet only. * There may be an electrical fault in the line. In this case, contact a qualified electrician to correct the electrical fault.
How to fix leaking between spa tub connectors and control unit connectors in Intex PureSpa SB-H10 Hot Tub?
If there's leaking between the spa tub connectors and the control unit connectors on your Intex Hot Tub: * Tighten the inlet and outlet connections. * If the spa control base inlet/outlet o-ring is missing or dirty, coat the o-ring with petroleum jelly for a waterproof seal.
What to do if the Intex PureSpa SB-H10 bubble air blower does not work?
If the bubble air blower on your Intex Hot Tub isn't working, it could be due to the air blower pump being too hot. Turn off and unplug the spa, let it cool down, and then restart it. If the problem persists, contact the Intex Service Center.
Why are air bubbles not as strong as before in my Intex PureSpa SB-H10 Hot Tub?
If the air bubbles in your Intex Hot Tub are weaker than before: * Ensure the o-ring is in place between the control base air outlet and spa tub air inlet connections. * Finger tighten all nuts on the air connections. * Use a repair patch to fix any punctures in the air bubble channel inside the tub. * If the air blower has failed, contact Intex Service Center.
What to do if my Intex Hot Tub filtration pump is not working?
If the filtration pump on your Intex Hot Tub isn't working, check the following: * Clean or replace the filter cartridge in time. * Check and clean the filtration inlet and outlet regularly. * If the filter pump motor has failed, contact the Intex Service Center.
What to do if my Intex PureSpa SB-H10 Hot Tub display isn't working?
If the display of your Intex Hot Tub isn't working, here are a few things to check: * Make sure the spa is plugged in and switched on. * Ensure the control panel cable is firmly attached to the control base. * Check your power source. * Reset the GFCI/RCD. If the GFCI/RCD is broken, contact the Intex Service Center.
Why is the air pressure weak during inflation of my Intex Bathtubs?
If the air pressure is weak during inflation of your Intex Bathtubs, ensure the o-ring is in place. Tighten or reinstall the hose adapter, and finger-tighten during inflation. If the issue continues, contact Intex Service Center.
Covers DANGER and WARNING notices for drowning, shock, and health risks.
Steps for testing the Ground Fault Circuit Interrupter (GFCI/RCD).
List and identification of all components included with the spa.
Key technical details and dimensions of the spa.
Guidelines for spa placement, leveling, and surrounding area preparation.
Step-by-step guide to inflating and deflating the spa tub and cover air bladders.
Instructions for connecting and securing the spa control unit to the tub.
Explains the purpose and use of each button on the control panel.
Information on the LED display and meaning of LED code chart entries.
Guidelines for keeping spa water clean, sanitized, and safe for users.
Procedures for cleaning the filter cartridge and changing spa water.
Details on maintaining ideal water chemistry including pH, alkalinity, and hardness.
Steps for draining, cleaning, and drying the spa tub.
Instructions for tightening the air valve to prevent leaks.
Information on maintaining and repairing the spa cover and its air bladder.
Proper methods for disassembling and storing the spa for off-season.
To Next Page
General