Need help?Do you have a question about the Invacare Pronto M6 and is the answer not in the manual?
General| Type | Power Wheelchair |
|---|---|
| Wheel Type | Pneumatic or Solid |
| Weight Capacity | 300 lbs. |
| Seat Width | 18 inches (45.7 cm) |
| Seat Depth | 16 inches (40.6 cm) |
| Motor Type | 24V DC |
| Drive Wheel Size | 10 inches (25.4 cm) |
| Weight | 180 lbs (without batteries) |
| Overall Width | 24.5 inches (62.2 cm) |
Defines symbols used to draw attention to specific footnotes or information within the catalog.
Details the format for listing measurements for screws, bolts, washers, and spacers.
Describes the kit contents, including carton, inserts, and foam for packaging.
Indicates the status of the Owner's Manual for the Pronto M6.
Lists available touch-up paint colors for the wheelchair.
Lists parts related to the front frame assembly, including strut housing and axle.
Lists parts for the rear frame assembly, including axle and covers.
Details hardware used for connecting frame components, like pins and screws.
Specifies hardware for the adjustable stop mechanism on the rear frame.
Shroud cover assembly that includes red decals.
Shroud decal assembly featuring blue decals.
Decal displaying the model name "Pronto M6".
Decal featuring the Invacare 3-D logo.
Kit containing shrouds and screws for front/rear axles.
Seat with headrest pillow in gray cloth (pre-2001) and vinyl (post-2001).
Headrest pillow available in gray cloth or vinyl.
Knob used for adjusting the lower arm position.
Strap used for positioning the seat.
Hardware kit for the seat adjusting collar.
Hardware required for mounting the seat to its stand.
Hardware components for seat struts and connecting pins.
The seat stand component itself.
Arm pad with arm tube sleeve for the right side, with retractable joystick mount.
Arm pad with arm tube sleeve for the left side, with retractable joystick mount.
Components for the arm assembly excluding the arm pad.
Package containing various hardware components for the arm assembly.
Knobs used for adjusting the arm position (lower and upper).
The complete rear wheel assembly, including the black rim.
Rear tire featuring a foam fill insert.
Hardware kit for mounting the rear wheel assembly.
Caster assembly for the rear of the wheelchair, 5-inch size.
Caster assembly for the front of the wheelchair, 6-inch size.
The gearbox assembly for the right and left sides of the motor.
Hardware kit for securing the gearbox assembly.
Switch assembly including necessary hardware for motor control.
Handles used to engage or disengage the free wheel function.
A package containing various hardware for motor and gearbox mounting.
Assemblies containing both the motor and brake components.
Replacement brushes for the motor.
Cables for charging the battery, including on-board and off-board types.
On-board and off-board chargers for the wheelchair battery.
Straps and AC cord associated with the charger.
Strap designed for carrying the battery.
Harness connecting power, circuit breaker, and cables.
30 AMP circuit breaker for the electrical system.
Assembly for covering the charger cable.
Hardware kit for mounting the electronic controller.
The primary electronic controller unit (MKIV).
Cable for motor and brake control, includes decals.
Potentiometer and knob for adjusting the speed setting.
Includes joystick boot, skirt, knob, and the RII joystick unit.
Kit containing screws, washers, bolts, and plug buttons for the footboard.
Safety pin component for the footboard assembly.
The entire footboard assembly, excluding certain parts.
Assembly kit including footboard, tube, washers, pin, and cable tie.
Safety pin component for the footboard assembly.
Support tube for the front rigging, in black.
Hanger for the front rigging, available for right and left sides.
Complete kit including instruction sheet for front rigging attachment.
Footrest support assembly for the right side.
Footrest support assembly for the left side.
Handles and springs used in the footrest release mechanism.
Kit containing hardware for mounting the slide tube.
Assemblies for the pivot/slide tube with footplates.
Legrest support assembly for the right side.
Legrest support assembly for the left side.
Handles and springs used in the legrest release mechanism.
The pad that provides cushioning for the legrest.
Tube assemblies for elevating the legrest.
Articulating legrest support assembly for the right side.
Articulating legrest support assembly for the left side.
Handles and springs used in the articulating legrest release mechanism.
Pad for the articulating legrest.
Hardware kit for the articulating legrest ratchet mechanism.
Pivot/Slide tube assemblies featuring plug buttons.
Pivot/slide tube assemblies with aluminum footplates.
Pivot/slide tube assemblies with composite footplates.
Black plug buttons used for various purposes.
Knob used for clamping or securing components.
Decals providing oxygen warning information in multiple languages.
Adhesive pads to prevent slipping.
Package containing protective caps.
Assembly for holding an oxygen cylinder.
Fasteners for attaching accessory tubes.
Rear basket for carrying items.
Holder for crutches or canes.
Safety flag for increased visibility.
Kit for attaching heel loops.
Details all the tools included in the power wheelchair tool kit.
To Next Page