INVENTOR AR1MVI-09WFR User Manual

O P E R A T I N G IN S T R U C T I O NS
Airflow directional co ntrol
O P E R A T I N G I N ST R U C T I O NS
Adjust the air flow direction prope rly, otherwise it might
cause discomfort or cause uneven room temperatures.
Adjust the horizontal louver using the remote controller.
Adjust the vertical louver manually.
Perform this function while the unit is in operation.
Use the remote controller to adju st the vertical air flow
direction. The horizontal louver can move slightly for each
press, or continuou sly swing up and down automatically.
Please refer to the RE MOTE CONTROLLER
OP
ERATION MANUAL for details.
Ad
justing vertical air flow( Up--Down)
Move the deflector rod manually to adjust the air flow
in the direction you prefer.
:Do not put your fingers into the panel of the
blower and su ction side.
Adjusting horizontal air flow (left - right)
IMPORTANT
The hig h-speed fan inside may
cause injury.
Do not operate the air conditioner for long periods with
the air flow direction set downward in cooling or
dehumidifying mode. Otherwise, condensation may
occur on the surface of the horizontal louver causing
moisture to drop on to the floor or on furnishings.
After a quick restart, the horizontal louver m ay remain
static for approximately 10 seconds.
Open angle of the horizontal louver should not be set
too small, as COOLING or HEATING performance may
be r educed due to too restricted
air flow area.
Do
not move the horizontal louver manually, o therwise
the horizontal louver will be out of sync. But if this
happens, please cea se oper ating, unplug power for
a few seconds,then r estart the air conditioner.
CAUTIO N
,,
,,
Basic operation modes: AUTO/COOL/DRY/HEAT
( ) Model dependent
How the air conditioner works
1 hour
1 hour
Set
Temperature
Set
Tempe rature
C oo l i ng
H e a t ing
SLEEP operation
1 hour
1 hour
SLEEP operation
7 hours timer off
7 hours timer o ff
AUTO operation
SLEEP ope ration
DRYING operation
HEATING operation
Optimal operation
When you set the air conditioner in AUTO mode, it will
automatically select cooling, heating(cooling/heating
models only), or fan only operation depending on set
temperature and the room temperature.
The air conditioner will control room temperature
automatically to the temperature point you set.
If you feel uncomfortable in the AUTO mode, you can set
your desired temperature.
When selected, the set temperature will increase (cooling)
o
r decrease (heating) by 1 C/2 F per hour for the first 2
hours. Thereafter it keeps this new temperature for 5
hours before switching off.
This operation saves energy and improves night time
comfort by synchronising with the body s metabolism.
The temperature is regulated while dehumidifying by
repeating turning on and off of the cooling operation or
fan only. The fan speed is LOW.
This air conditioner operates on the heat-pump principle,
absorbing heat fro
m air outdoors and transferring that
heat to the indoor unit. As a result, the operating
performance is reduced as outdoor air temperature drops.
If you feel that the heating performance is insufficient, we
recommend you to use this air conditioner in conjunction
with other kinds of heating appliance.
To achieve optimal performance, please note the
following:
Adjust the air flow direction correctly so that it is not
torwards people.
Adjust the temperature to achieve moderate comfort
le
vels. Excessively low or high temperature waste
energy.
Improve performance by keeping w indows and doors
closed.
Limit energy usage(run time) by using the TIMER
function.
Do not put any object near air inlet or air outlet, as the
efficiency of the air conditioner may be reduced and may
cause the air conditioner to stop running.
Inspect the air filters periodically, and clean them when
needed.
O O
,

INVENTOR AR1MVI-09WFR Specifications

General

Brand	INVENTOR
Model	AR1MVI-09WFR
Category	Remote Control
Language	English