Iseki TC213F - User Manual

This document is an operation manual for the ISEKI TC213F tractor, a 4WD model designed for various agricultural tasks. The manual provides comprehensive information on safe operation, maintenance, and technical specifications to ensure optimal performance and longevity of the machine.

Function Description

The ISEKI TC213F is a compact 4WD tractor primarily designed for agricultural operations. It features a diesel engine and is equipped with a power take-off (PTO) system, a three-point hitch for implement attachment, and various control levers for speed, direction, and implement management. The tractor is capable of performing tasks such as tilling, mowing, spraying, and hauling, depending on the attached implements. Its 4WD capability enhances traction and maneuverability, especially on challenging terrain.

Important Technical Specifications

• Engine: ISEKI Diesel, E269-E03 model, indirect injection, overhead valve.
  • Displacement: 0.688 liters (688 cc).
  • Number of cylinders: 2.
  • Bore: 78 mm.
  • Stroke: 72 mm.
  • Engine horsepower (net) KW(PS)@ engine rpm: 9.1(13)/2700.
  • PTO horsepower (estimate) KW (PS): 8.1(11).
  • Firing order: 1 - 2.
  • Compression ratio: 22.5.
  • Low idle speed: 1050 min⁻¹ (rpm).
  • High idle speed (unloaded): 2970 min⁻¹ (rpm).
  • Valve clearance (cold) - intake and exhaust: 0.25 mm.
  • Air cleaner: Single - dry element.
  • Engine cooling: Liquid, forced circulation.
  • Cold starting: Glow plugs (2).
• Transmission:
  • Primary: F3/R1.
  • Range: F3/R2.
  • Gear selections: F6/R4.
  • Clutch: Wet multi-disc (Dia: 112 mm).
  • Brakes: Mechanically actuated wet discs on agricultural tyres.
  • Speed range (km/h):
    • Forward: 0.72 to 13.11 km/h (6 speeds).
    • Reverse: 0.90 to 5.47 km/h (4 speeds).
• Power Take-Off (PTO):
  • Control: Lever and pedal.
  • Rear PTO shaft: 35 mm (1.375 in) diameter – six spline.
  • Output: Clockwise rotation.
  • Speeds @ engine min⁻¹ (rpm): 540 @ 2581.
• Hydraulics:
  • Main hydraulic system: Gear pump (Open centre).
  • Output - maximum: 8.97 liters/min.
  • Pressure - relief valve setting: 120 kgf/cm².
  • Rear linkage type: Three-point hitch.
  • Control: Operated by single 'position' control lever.
  • Lift capacity: 380 kg measured at link ends.
• Electrical System:
  • System voltage: 12 volt - negative (-) ground.
  • Battery cca @ -18°C (0°F): 332 cca.
  • Charging: 8.5 amp alternator with outer regulator (E4 sub-model), 40 amp alternator with internal regulator (GE4 sub-model).
• Capacities:
  • Engine crankcase with filter: 2.2 liters.
  • Transmission and differential housing (including hydraulics): 12.0 liters.
  • Fuel tank: 13 liters.
  • Cooling system: 3 liters.
  • Front axle - four-wheel drive: 2.7 liters.
• Track Setting:
  • Front four-wheel drive:
    • Agricultural tyres (dished in only): 755 mm.
    • Turf tyres (dished in only): 855 mm.
  • Rear two-wheel drive:
    • Agricultural tyres (adjustable wheels): 750 and 920 mm.
    • Turf tyres (dished in only): 830 and 845 mm.
• Maximum Axle Loading:
  • Front four-wheel drive - both models: 400 kg.
  • Rear axle - both models: 450 kg.
• Tyre Size:
  • Front:
    • Agricultural tyre: 4.50-10 2PR.
    • Turf tyre: 20x8.00-10.
  • Rear:
    • Agricultural tyre: 7-16 4PR.
    • Turf tyre: 212/80D-15.
• General Dimensions:
  • Overall length: 2240 mm.
  • Minimum width: 920 mm.
  • Wheelbase: 1050 mm.
  • Minimum ground clearance: 255 mm.
  • Turning radius (4WD engaged): 1.5/1.6 m (with brake), 1.7 m (without brake).
  • Turning radius (2WD disengaged): 1.5 m (with brake), 1.7 m (without brake).
  • Weight (without ROPS and seat): 475/470 kg.

Usage Features

• Safety First: The manual emphasizes safety with DANGER, WARNING, and CAUTION labels throughout. Operators are instructed to read the manual thoroughly, wear appropriate protective gear, and never allow unauthorized persons to operate the machine.
• Controls Layout: The instrument panel includes a fuel gauge, combination switch (horn, headlamp, position lamp, turn signal), battery charge lamp, engine oil pressure warning lamp, coolant temperature warning lamp, hourmeter, main switch, hazard signal switch, parking lamp switch, main beam switch, turn indicator lamp, hazard lamp, and trailer lamp.
• Starting the Engine: Requires placing the throttle at full or mid position, depressing the clutch pedal, ensuring gear shift lever and PTO are in neutral, pre-heating with glow plugs (if cold), and operating the starter for no longer than 10 seconds.
• Warm-Up Period: Essential for cold engines, especially in low ambient temperatures, to lubricate all components and warm hydraulic fluid. Recommended warm-up times vary from 5 to 30+ minutes depending on temperature.
• Travelling: Operators must latch brake pedals together, ensure differential lock is off, avoid sharp turns at high speeds, and drive carefully on poor footing or slopes.
• Implement Operation: The PTO lever engages/disengages the PTO drive system. The three-point hitch control lever (position select) manages implement height.
• Differential Lock: Engaged by depressing a pedal, it locks both rear axles together for improved traction. It should be disengaged for turning to prevent damage and maintain steering ability.
• Four-Wheel Drive: Engaged by a lever, it provides power to both front and rear axles for enhanced traction. The front axle should be disengaged when transporting on hard, dry surfaces to prevent tyre wear and driveline damage.
• Loading/Unloading: Requires setting slip-proof ramps, driving straight at slow speeds, interlocking brake pedals, and securing the tractor to the truck for transport.

Maintenance Features

• Periodic Maintenance Schedule: The manual provides a detailed table for inspection and servicing intervals for various components, including engine oil, air cleaner, engine coolant, fuel strainer, fan belt, electrolyte level, engine oil filter, transmission oil, hydraulic oil filter, clutch pedal play, brake pedal play, brake performance, throttle lever and foot throttle, control lever performance, tyre pressure, toe-in, wheel tightening bolts, front axle oil, grease-up, radiator screen, electrical apparatus, electrical wiring, air intake openings, bolts and nuts, and rubber pipes.
• Lubrication: Specific instructions for engine oil, transmission oil, hydraulic oil, front axle oil, and grease fittings, including types of lubricants and fill points.
• Cooling System: Regular cleaning of the radiator screen and checking/replenishing coolant levels are crucial.
• Fuel System: Instructions for checking fuel levels, replacing fuel filters, and air-bleeding procedures.
• Electrical System: Guidelines for maintaining electrical wiring, handling the battery safely, and managing fuses.
• Storage: Procedures for short-term and long-term storage, including cleaning, covering, removing the battery, and draining coolant/fuel if necessary.
• Troubleshooting: A comprehensive section outlining common problems, possible causes, and remedies for engine, clutch, brakes, hydraulic system, steering system, and electrical system issues.
• Pre-Delivery Inspection: A checklist for dealers to ensure the tractor is properly inspected and prepared before delivery to the customer.

The manual emphasizes the importance of following all instructions for safe and proper operation, adjustment, and servicing to ensure the tractor's optimum performance and to prevent damage or injury. It also advises consulting an ISEKI dealer for any questions or issues.