ISHIDA CCW-R-224B-14-SS

Questions and Answers

L
Linda HaleAug 18, 2025
What to do if the ISHIDA Industrial Equipment weigher doesn't operate when the remote control is ON?
- F
  fgriffinAug 18, 2025
  If the ISHIDA Industrial Equipment weigher doesn't operate when the remote control unit is turned on, several issues could be the cause: * A blown fuse: Replace fuses f601 through f604 of the AC fuse board (P-5507*). These are standard machine midget fuses (250V 3.15A) located in the PS-0 unit. * RCU board malfunction: Replace the RCU board (P-970*). * Component malfunction: Replace the KM01 (electromagnetic contactor) located in the PS-0 unit. * Interlock signal not input: Replace the relay board (P-5506*). Also, check the connection between the relay board (P-5506*) XJ454 and WCU board (P-5561*) J305 if the LED for the switch monitor blinks normally. * FDC board malfunction: Replace the FDC board (P-5532*) if the [Power] key cannot be turned on.
M
martinezedwardAug 20, 2025
How to troubleshoot a blank screen on the ISHIDA CCW-R-224B-14-SS remote control unit?
- T
  Taylor ReynoldsAug 20, 2025
  If nothing is displayed on the screen of the remote control unit for your ISHIDA Industrial Equipment, it could be due to: * A breaking or poor connection: Check XC21 connector (PS-RCU unit) and XJ1 connector (Remote control BOX unit) to ensure they are properly connected. * Display malfunction: Replace the switching power (PS-RCU unit U01), the RCU board (P-970*), or the LCD.
P
Patricia WhiteAug 23, 2025
What to do if ISHIDA CCW-R-224B-14-SS Industrial Equipment displays a Hopper Error (PH, WH)?
- N
  Nicole WhiteAug 23, 2025
  If your ISHIDA Industrial Equipment displays a Hopper Error (PH, WH), consider the following potential causes and solutions: * Loose screw on the cam sensor: Repair the weigh drive unit. * Board malfunction: Replace the cam sensor board (P- 5207*) or the DUC board (P-5579*/P- 5524*). * Connector issue: Check the conductivity of the DUC board (P-5579*/P-5524*) connector. * Blown fuse: Replace the midget fuse on the DC fuse board (P-5508*) (PS-0 unit). Use a 125V 5A fuse. * Weigh drive unit malfunction: Repair or replace the weigh drive unit.
F
fperkinsAug 26, 2025
Why is my ISHIDA CCW-R-224B-14-SS showing a Hopper Error (BH, RS, TH, DTH)?
- S
  swilliamsAug 26, 2025
  If your ISHIDA Industrial Equipment shows a Hopper Error (BH, RS, TH, DTH), the following could be the cause: * Loose screw on the cam sensor: Repair the drive unit. * Board malfunction: Replace the cam sensor board (P- 5207*) or the DUC board (P-5579*/P- 5524*). * Connector issue: Check the conductivity of the DUC board (P-5579*/P-5524*) connector and the WCU board (P-5561*) connector. * Blown fuse: Replace the midget fuse on the DC fuse board (P-5508*) (PS-0 unit). Use a 125V 5A fuse. * Drive unit malfunction: Repair or replace the drive unit.
K
Kelly VillaAug 28, 2025
Why does the feeder not operate on my ISHIDA CCW-R-224B-14-SS Industrial Equipment?
- B
  bmorrisAug 28, 2025
  If the feeder on your ISHIDA Industrial Equipment is not operating, check the following: * Blown fuse: Replace fuses f601 through f604 of the AC fuse board (P-5507*). Use a standard machine midget fuse (250V 3.15A) located in the PS-0 unit. * Board malfunction: Replace the FDRV board (P-5578*) or FDC board (P-5532*) located in the main electrical unit.
M
Michelle JonesAug 30, 2025
What to do if the main power breaker shuts down on ISHIDA CCW-R-224B-14-SS Industrial Equipment?
- H
  Howard HaydenAug 31, 2025
  If the main power breaker shuts down on your ISHIDA Industrial Equipment, it could be due to: * Electric leakage of the weighing machine: Check for electric leakage and short circuit. * Short circuit in the electrical circuit of the weighing machine.
J
Jonathan SmithSep 2, 2025
How to correct weight discrepancies on ISHIDA CCW-R-224B-14-SS Industrial Equipment?
- M
  Mrs. Yvonne KentSep 2, 2025
  If the weight of the product is significantly different from the displayed weight on your ISHIDA Industrial Equipment, the setting of the head specification switch on the DUC board may be incorrect. Check the test drive and set correctly by SW1 on the DUC board (P-5579*/P- 5524*) in the DUC unit.
S
Stanley JohnsonSep 5, 2025
What causes an [OVERSCALE ERROR] on ISHIDA CCW-R-224B-14-SS?
- H
  heatherhowardSep 5, 2025
  An [OVERSCALE ERROR] on ISHIDA Industrial Equipment may be caused by infeed control phototube malfunction. Replace the phototube to avoid pooling of the product caused by not being able to control the amount of product supplied to the feeder.
S
Suzanne MunozSep 7, 2025
What to do if ISHIDA CCW-R-224B-14-SS Industrial Equipment displays a [ZERO ERROR]?
- C
  Chelsea JonesSep 7, 2025
  If your ISHIDA Industrial Equipment displays a [ZERO ERROR], here are some potential solutions: * Board malfunction: Replace the ADC board (P-5576*) if zero cannot be obtained even when J320 to J322 are disconnected. Alternatively, replace the preamp board (P-5527*). * Weigh mechanism malfunction: Replace the load cell. * ±15V power malfunction: Check the ADC board (P-5576*) J324 connector and replace the PS-CAL unit.
A
Ashley HooverSep 9, 2025
What causes a '[WARNING: NO TRANSMISSION]' error on ISHIDA CCW-R-224B-14-SS?
- C
  Cheryl LandrySep 10, 2025
  A '[WARNING: NO TRANSMISSION]' error on ISHIDA Industrial Equipment may be due to a connector breaking or poor connection. Check the conductivity of the following connectors: J350 (ADC board P-5576*), XT601 (PS-0 unit), XJ455 (relay board P-5506*), XJ453 (relay board P-5506*), and XJ384 (DMU board P-5562*).