Why does my ITV ICE MAKERS Ice Maker run and stop alternatively?
If your ITV ICE MAKERS Ice Maker runs and stops intermittently, it might be due to the safety pressure switch opening. To resolve this, clean the air condenser located behind the front grid.
What to do if my ITV ICE MAKERS SPIKA NG 130 Ice Maker has no water in the tray?
If there is no water in the tray of your ITV ICE MAKERS Ice Maker, the issue could be due to a lack of incoming water. Check the water supply to ensure it is connected and functioning correctly. Alternatively, the inlet strainer at the water valve may be blocked. Inspect and clean the strainer to ensure proper water flow.
How to fix difficult to release ice slab at harvest in ITV ICE MAKERS Ice Maker?
If you're finding it difficult to release the ice slab during harvest with your ITV ICE MAKERS Ice Maker, there are a couple of potential causes. First, the unit might not be leveled correctly, possibly tilted to the back. Level the unit, lowering the front. Second, there might not be enough harvest time. In that case, add more pins to the cam timer wheels, following the label indications.
What to do if my ITV ICE MAKERS SPIKA NG 130 has none of the electrical parts working?
If none of the electrical parts in your ITV ICE MAKERS Ice Maker are working, there could be a few reasons. First, ensure the machine is plugged in and verify the socket has power. Second, the bin thermostat might be open because ice is touching the bin tube; remove the ice from the bin. Third, the bin thermostat might be open even without ice touching the bin tube; in this case, adjust the thermostat located in the electric box under the top cover.
Why is ice slab empty or too thick in my ITV ICE MAKERS SPIKA NG 130 Ice Maker?
If the ice slab in your ITV ICE MAKERS Ice Maker is either empty or too thick, it could be due to a disadjusted cycle time. Adjust the thermostat located in the electric box under the top cover.
What to do if all the electrical parts work but not compressor in ITV ICE MAKERS SPIKA NG 130 Ice Maker?
If all the electrical parts in your ITV ICE MAKERS Ice Maker are working except for the compressor (and the water doesn't get frozen), the compressor switch might be in the “WASH” position (0). Switch it to the “ICE” position (1).
Why ITV ICE MAKERS Ice Maker doesn't stop when the bin is full?
If your ITV ICE MAKERS Ice Maker doesn't stop when the bin is full and ice is touching the thermostat tube, the bin thermostat might not be opening (it only operates at harvest time). Adjust the thermostat located in the electric box under the top cover.
How to fix not uniform flow pattern at evaporator in ITV ICE MAKERS SPIKA NG 130 Ice Maker?
If you notice a not uniform flow pattern at the evaporator of your ITV ICE MAKERS Ice Maker, it could be due to a dirty or scaled distributor. Perform a descaling procedure and clean the distributor after removing it from the two clips at its sides.
Covers intended use, installation, grounding, modifications, and general safety precautions.
Addresses safety precautions for appliances using flammable refrigerants, including ventilation and leakage.
Instructions for inspecting packaging and equipment for damages upon receipt from the carrier.
Guidelines for selecting a suitable location, considering temperature, ventilation, and clearances.
Procedure for ensuring the ice machine is perfectly leveled using adjustable feet.
Recommended minimum distances to obstacles for efficient operation and servicing.
Illustrates water, drain, and electrical connection points for undercounter models.
Details on water quality, pressure, and the need for filters or regulators.
Guidelines for proper drain pipe installation, including slope and diameter.
Emphasizes mandatory grounding and proper electrical connection procedures.
Instructions for installing modular units on top of bins, verifying stability and fasteners.
Checklist of essential checks before starting the machine, including leveling and utilities.
Details on electrical diagrams, dip switch settings, and factory default adjustments.
Describes the initial power-on sequence, including delays and pressure relief.
Explains the compressor energizing and water freezing process.
Details the hot gas valve operation and ice slab release into the bin.
How the machine stops automatically when the ice storage bin is full.
User's responsibility for sanitary conditions and periodic cleaning of water systems.
Step-by-step instructions for cleaning the water distribution system for undercounter models.
Procedures for cleaning and sanitizing the ice storage bin for undercounter models.
Instructions for cleaning the air condenser using a vacuum, brush, or low-pressure air.
Guidelines for cleaning the exterior surfaces with mild soap and water or stainless steel cleaner.
Procedure for checking water connections, tubes, and hoses to prevent leaks.
Troubleshooting steps for issues where none of the electrical parts work.
Solutions for problems with the compressor not working or water not freezing.
Troubleshooting for no water in the tray or issues with ice slab thickness.
Resolving issues like the machine not stopping when the bin is full or intermittent operation.
General| Brand | ITV ICE MAKERS |
|---|---|
| Model | SPIKA NG 130 |
| Category | Ice Maker |
| Language | English |
To Next Page
