Jack H2 - User Manual

 1/14

简易款厚料机系列电控使用说明书
Simple electric control box manual
安全事项
· 在使用本产品之前，请先阅读《使用说明书》及所搭配的缝纫机机械说明书。
· 本产品必须由接受过专业培训的人员来安装或操作。
· 请尽量远离电弧焊接设备，以免产生的电磁波干扰本控制器而发生误动作。
· 请不要在室温 45°以上或者 0°以下的场所使用。
· 请不要在湿度 30%以下或者 95%以上或者有露水和酸雾的场所使用。
· 安装控制箱及其他部件时，请先关闭电源并拔掉电源插头。
· 为防止干扰或漏电事故，请做好接地工程，电源线的接地线必须牢固的与大地有效连接。
· 所有维修用的零部件，须由本公司提供或认可，方可使用。
· 在进行任何保养维修动作前，必须关闭电源并拔掉电源插头。控制箱里有高压危险，必须关闭电源五分
钟后方可打开控制箱。
· Safety Precautions
· Before using this product, please read the User's Guide and the manual of the machine attached with it.
· This product must be installed or operated by professionally trained personnel.
· Please keep away from the arc welding equipment to avoid the electromagnetic wave from interfering with the
controller.
· Please do not use it at room temperature above 45°or below 0°。
· Please do not use it in places with humidity below 30% or above 95% or where there is dew and acid mist.
· When installing the control box and other parts, turn off the power and unplug the power plug.
· To prevent interference or electric leakage accidents, make a good grounding work. The grounding wire of the
power cord must be firmly connected to the earth.
· All parts for maintenance must be supplied or approved by the Company before they can be used.
· The power must be turned off and the plug unplugged before any maintenance action is performed.There is a
high-voltage danger in the control box. You must shut down the power for 5 minutes before opening the control
box.
·
1 产品安装 Product installation
1.1 产品规格 Product specification
电源电压
su
pp
l
y
volta
g
e
AC 220±20% V
电源频率 supply
fre
q
uenc
y
50Hz/60Hz
最大输出功率
Maximum power
out
p
u
t
750W
1.2 接口插头的连接 Connection of interface plug
将脚踏板及机头的各连接插头安插到控制器后面对应的插座上，各插座名称如图 1-2-2 所示。连接
好，请检查插头是否插牢。
Plug the pedals and heads into the corresponding receptacle behind the controller, as shown in figure
1-2-2.After connection, check that the plug is plugged in.

Jack H2 Specifications

General

Stitch Length	5mm
Needle Type	DBx1
Lubrication	Automatic
Hook	Rotary Hook
Voltage	220V
Category	Sewing Machine
Max Sewing Speed	5000 stitches per minute
Motor Type	Servo Motor
Model	H2

Summary

Safety Precautions

General Safety Warnings

Important safety guidelines for installation, operation, and maintenance of the control box.

Environmental and Usage Conditions

Recommended environmental conditions and usage restrictions for the control box.

Product Installation

Product Specification

Specifies the electrical and power requirements of the control box.

Connection of Interface Plug

Guides on connecting pedals and machine heads to the controller sockets.

Wiring and Grounding

Emphasizes the importance of proper wiring and grounding for safe operation.

Operation Panel Usage Instructions

Panel Display Overview

Explains the display elements and indicators on the operation panel.

Key Function Description

Details the function of each button on the operation panel.

Parameter Adjustment

Operator Parameter Mode and Save

Instructions for entering and saving operator parameter settings.

Technician Parameter Mode and Save

Instructions for entering and saving technician parameter settings.

Speed Adjustment

How to adjust sewing speed using the panel buttons.

Restore Factory Settings

Procedure for resetting the control box to factory defaults.

Enter Monitoring Mode

How to enter and use the monitoring mode for system parameters.

Operator Parameters List

Detailed list and explanation of operator-configurable parameters.

Technician Parameters List

Detailed list and explanation of technician-configurable parameters.

Monitoring Parameters List

Detailed list and explanation of parameters for monitoring system status.

Error Code and Alarm Sheet

Error Code Sheet

Lists error codes, their meanings, and troubleshooting solutions.

Safety Alarm Sheet

Lists safety alarms, their meanings, and resolution steps.

Pedal Sensitivity Adjustment

Pedal Sensitivity Adjustment Guide

Instructions for adjusting the sensitivity and operation of the foot pedal.