Jacuzzi J-SN180W - Using the Bath Fill Function; Bath Fill Function Overview and Settings; Bath Fill Operation Steps; Bath Fill Safety and Usage Notices


32 JacuzziSignatureWaterHeatersJ‐S180/J‐S199
SengtheWaterVolumeandTemperature
UsingtheBathFillFuncon
Overview
ThisfunconisexclusivetotheJ‐C200temperature
controller.Thebathfillfunconallowstheconsumer
tofillatubwithapresetvolumeofwateratapreset
temperature.Thisisdonebypressingthebathfill
buonontheJ‐C200controllerwhile
nohotwateris
flowingandthenopeningonlythehotwatertap.The
waterheaterwillstopthehotwaterflowwhenthe
presetvolumehasbeenreached.Thehotwatertap
shouldthenbeclosedandthebathfillbuon
pressed.
Thetemperaturesengsfor
thebathfillfunconare
limitedtothoseinthetablebelow.

 BathFillTemperatureSengsAvailable
°F 98 100 102 104 106 108 110 115 120
°C 37 38 39 40 41 42 43 46 49
1. Pressthe“PriorityMode”
buononthetemperature
controller.ThegreenPriority
lightwillglowindicangthat
thiscontrolleriscontrollingthe
temperatureandthatthewater
heaterisreadytosupplyhot
water.
2. Pressthe“BathFill”buonto
setthewatervolumeand
temperature.

3. Pressthe“Temp”up(+)or
down(‐)buonstoobtainthe
desiredtemperatureseng.

4. Pressthe“WaterVol.”up(+)or
down(‐)buonstoobtainthe
desiredwatervolumein
gallons.

5. Pressthe“BathFill”buon.
Thedefault
volumeissetto25gallons.Thevolume
canbesetbetween10and120gallons.
Mulple
Water
Heaters
Thebathfillfunconwillnotwork
properlyifitisconnectedtomulple
waterheaters.Thetubwilloverfill
becausethebathfillfunc onisnotable
tomeasurethewatervolumewhen
connectedtomulplewaterheaters.
NO TICE
Power
Loss
Ifpowerislostduringthebathfill
funcon,thewaterheaterwill shutdown
butthewaterwillconnuetoflow.
Whenpowerreturns,thewatershutsoff
anddiagnosccode03appearsonthe
controller.
Ifpowerislostaerthebathhasfi
lled
butbeforethebathfillfunconbuonis
de‐selected,thenthewaterwillnotflow
duringthepowerlossoraerthepowe r
isreturned.Oncepowerreturns,close
thehotwatertapandde‐selectthebath
fillfuncon.Nodiagnosc
codeappears.
NO TICE
An‐
scald
Fixtures
Donotusewithsinglehandlefixtures
thathavean‐scaldfeaturesbuiltinto
them.Thesefixturesallowa
predeterminedamountofcoldwater
whichisnottakenintoaccountbythe
bathfillfuncon.
NO TICE
To
Prevent
Over
Filling
Becarefulnottooverfillthebath.An
averagebathvolumeis60gallons.When
fillingthebathusingthisfunconforthe
firstme:
• Monitorandremainbythebathwhile
thewaterisrunning.
• Usealowbathfillvolumelessthan
25gallons
NO TICE
Bath Fill
Bath Fill