To Next PageTo Next Page
Need help?Do you have a question about the Jacuzzi J-SN180W and is the answer not in the manual?
General| Model | J-SN180W |
|---|---|
| Capacity | 180 Liters |
| Power Source | Electric |
| Voltage | 220-240V |
| Thermostat | Adjustable |
| Type | Storage Water Heater |
| Power | 3000W |
| Safety Features | Pressure Relief Valve |
| Warranty | 5 years |
Explains safety alert symbols like DANGER, WARNING, CAUTION.
Precautions to take before performing maintenance, including power and gas shutoff.
Alerts users to the danger of burns from hot exhaust and water components.
Details the necessary skills and knowledge for professional installation to ensure safety and warranty validity.
Covers essential DO NOT and MUST DO instructions for a compliant and safe installation process.
Identifies components provided with the unit and essential tools for installation.
Lists optional tools and materials that may be needed for a complete installation.
Evaluates water quality parameters that can damage the heat exchanger and affect performance.
Addresses air quality concerns and corrosive compounds affecting appliance longevity and performance.
Details required clearances from various building features and grade for vent termination.
Provides specific rules regarding vent termination placement near sidewalks and open structures.
Advises avoiding dryer vents and commercial exhaust, and maintaining minimum ground clearance.
Details specific considerations for vent termination locations under overhangs to prevent exhaust recirculation.
Guides on avoiding dryer vents and commercial exhaust for outdoor unit vent terminations.
Details required clearances for indoor units from combustibles and for servicing.
Details required clearances for outdoor units from combustibles and for servicing.
Guides on determining maximum vent length based on elbows and adjusting the relevant DIP switch.
Advises on protecting the unit from freezing, noting warranty exclusions and recommending protective measures.
Ensures the installation location meets all environmental, clearance, water, electrical, and code requirements.
Details how to mount the unit to the wall and safely remove the front panel.
Lists recommended manufacturers and their specific vent systems certified for the water heater.
Covers DO NOT and MUST DO rules for proper vent system installation, including direct venting and support.
Advises on considerations for enclosing vent systems and warranty implications.
Shows horizontal termination methods, with or without a condensate collector, and related warnings.
Details the configuration for vertical vent termination, requiring a condensate collector.
Details how to adjust the condensate collector position and secure the vent component.
Outlines DO NOT and MUST DO instructions to prevent condensate damage to the heat exchanger.
Provides details on condensate traps, cold climates, and pipe slope recommendations.
A checklist to verify proper venting clearances, product use, slope, and vent system length.
Details installation, rating, and discharge requirements for the pressure relief valve.
Recommends isolation valves and specifies piping requirements for potable water systems.
Illustrates a standard piping configuration for connecting the water heater to water supply and gas.
Explains the symbols used in the piping diagram for valves, regulators, and pumps.
Guides on connecting cold and hot water lines to the respective inlet/outlet ports of the water heater.
Ensures proper purging, leak-free lines, correct pressure relief valve, and clean water filter.
Emphasizes safety precautions and general requirements for gas line installation.
Explains factors influencing gas pipe sizing and reference to National Fuel Gas Code.
Provides recommended pipe sizes for natural gas based on length and capacity.
Offers recommended pipe sizes for propane gas based on length and capacity.
Details grounding, power source, and outlet requirements, prohibiting extension cords.
Explains how to set DIP switches 2 and 3 for different altitudes to optimize gas pressure.
Guides on adjusting SW1 DIP switch No. 1 for maximum vent length compliance.
Confirms proper gas supply, electrical connection, grounding, and absence of extension cords.
Advises on optimal controller placement and specifies cable types and lengths for connectivity.
Provides step-by-step instructions for physically mounting the controller and connecting its wiring to the unit.
Ensures all installation steps, clearances, safety checks, and code requirements are met before operation.
Covers explaining operation, safety, maintenance to the customer and providing the manual.
Details key performance metrics like gas consumption, hot water capacity, energy factor, and electrical requirements.
Lists gas supply pressure, certifications, and compliance with emissions standards.
Provides detailed measurements and connection port locations for indoor units.
Details the physical measurements and connection port locations for outdoor units.
Graphical representation of pressure loss versus water flow rate for different models.
Displays water flow rate against temperature rise for various models, indicating performance characteristics.
Illustrates the internal electrical components and their interconnections using a ladder logic format.
Highlights critical safety information and precautions before operating the water heater.
Provides immediate steps to take if a gas smell is detected, emphasizing safety and professional contact.
Lists essential safety rules for users, including ignition type, gas detection, and appliance condition.
Guides users through the process of starting up and operating the water heater safely.
Outlines the correct steps for safely shutting off the gas supply to the appliance.
Describes the J-C100 controller's features, dimensions, and how to lock/unlock its settings.
Details the J-C200 controller's display, buttons, and functions for spa applications.
Explains the need for minimum flow and how to adjust temperature settings for optimal performance.
Warns about scalding hazards and provides guidelines for safe water temperatures and testing.
Outlines steps for setting temperature and highlights important notices regarding adjustments and default settings.
Lists available temperature settings in Fahrenheit and Celsius when using a controller.
Explains how to set default temperatures (120°F or 140°F) using DIP switches when no controller is installed.
Covers muting controller beeps and adjusting voice prompt volume on the J-C200 Spa Controller.
Explains the function's purpose, temperature limits, and how to set water volume and temperature.
Guides users through the process of filling a bath using the J-C200 controller's bath fill feature.
Warns about potential issues like multiple heaters, power loss, and anti-scald fixtures.
Covers the procedure for filling a bath, stopping the process, and related safety notices.
Guides on how to display diagnostic codes, water flow, and temperature data.
Provides remedies for common diagnostic codes related to power, air supply, ignition, flame, thermal fuse, and over-temperature.
Lists remedies for various codes covering electrical, sensor, burner, fan, water flow, PC board, and leak detection issues.
Outlines annual inspection requirements and procedures for cleaning internal components, motors, and the cabinet.
Details tasks like cleaning the water filter, addressing lime build-up, and clearing snow from vent terminals.
Covers annual testing of the relief valve and visual checks for satisfactory burner flame patterns.
Provides steps for safely shutting off utilities and draining the unit for winter storage.
Advises on covering vent terminations to prevent debris entry during winter.
Step-by-step guide for flushing the heat exchanger with vinegar to remove scale build-up.
Illustrates the plumbing setup for flushing and defines the symbols used.
Step-by-step instructions to drain the water heater for maintenance or storage.
Outlines the steps to safely restore the water heater to operation after it has been drained.
Suggests a method to prevent freezing by circulating low volumes of water during cold weather.
Details specific state regulations for side wall venting, carbon monoxide detectors, and signage.
Lists part numbers for gas control assembly, electrode/flame rod, and ignitor, with visual references.
Identifies part numbers for heat exchanger, water flow servo, and bypass servo assembly with images.
Shows part numbers for PC board, fan assembly, water filter, and thermal fuse harness with visual aids.
Outlines what is covered under warranty, duration for different parts, and exclusions for circulating systems.
Explains Jacuzzi's process for repair, replacement, and handling of warranty claims.
Provides instructions on how to get service, register the product, and required proof of purchase.
Lists conditions not covered by warranty and limitations on implied warranties and consequential damages.
