To Next PageTo Next PageWhy is there no power and the green LED is off on my JBL Spot Subwoofer?
If there's no power and the green LED isn't lit, check that the wall adapter is correctly plugged into the JBL Spot subwoofer and that the wall outlet is providing power. You can test the outlet with a lamp or another device to confirm it's working.
What to do if my JBL Subwoofer has no volume or low volume?
If your JBL Subwoofer has no volume or low volume, touch the volume “Up” (+) pad on the volume control to un-mute and/or increase the system volume level. Touching the volume “Down” (–) pad lowers the system volume. Touching both the (+) and (–) volume control pads at the same time will mute the system.
How to increase the volume if the input source is low on JBL Subwoofer?
If the input source is low, increase the volume level on the audio source device.
What to do if there is no sound from my JBL Spot stereo system?
If you're not getting any sound from your JBL Spot stereo system, here are a few things to check: * **Power:** Make sure the power supply is properly connected to a working power outlet and to the JBL Spot subwoofer. A green LED should light up on the subwoofer when it's powered on. * **Volume:** Ensure the volume isn't muted or set too low. Use the volume “Up” (+) pad to increase the volume. Note that touching both the (+) and (–) pads simultaneously will mute the system. * **Source Volume:** Verify that the volume level on your audio source device is turned up.
Why is there no power to my JBL Spot stereo system and the green LED is off?
If your JBL Spot stereo system isn't powering on and the green LED is off, the issue might be: * **Adapter Connection:** Ensure the wall adapter is correctly plugged into the JBL Spot. * **Outlet Functionality:** Test the wall adapter in a known working outlet. You can test the outlet by plugging in a lamp or another device.
What to do if there is no volume control on the right satellite speaker of my JBL Spot stereo system?
If the volume control isn't working on the right satellite speaker of your JBL Spot stereo system, consider the following: * **Satellite Connection:** Ensure the right satellite speaker is properly connected to the subwoofer. Press it firmly into the subwoofer. * **Incorrect Connection:** Make sure that left and right satellites are connected to correct subwoofer connector. To further isolate the problem, connect your JBL Spot to a known audio source and test the audio source with headphones.
How to adjust the bass on my JBL Spot stereo system?
If you're experiencing a lack of bass with your JBL Spot stereo system, check the satellite connections by pressing them firmly into the subwoofer. Then, adjust the Sub Level knob located on the rear of the subwoofer to achieve your desired bass level.
Why is there no bass on my JBL Subwoofer?
If there's no bass, check the satellite connections by pressing them firmly into the subwoofer. Then, adjust the Sub Level knob on the rear of the subwoofer to your desired bass level.
General| Type | Portable speakers |
|---|---|
| Power requirements | 230 VAC |
| Number of satellite speakers | 2 |
| Satellite speakers RMS power | 12 W |
| Subwoofer dimensions (WxHxD) | 200 x 200 x 140 mm |
| Audio output channels | 2.1 channels |
| Impedance | 5000 Ω |
| Frequency range | 40 - 20000 Hz |
| RMS rated power | 36 W |
| Signal-to-Noise Ratio (SNR) | 80 dB |
Weight and Dimensions| Weight | 2800 g |
|---|
Statement on device compliance with FCC rules and conditions.
Guidelines for minimizing radio and television interference from the device.
Read instructions, retain for reference, heed warnings, and follow all instructions.
Do not remove cover; refer servicing to qualified personnel to prevent electric shock.
Avoid extreme temperatures, humidity, direct sunlight, dust, vibrations, and excessive force.
Use appropriate cleaning cloths, avoid feedback, light sources, and protect media from magnetic fields.
Steps for unpacking components and connecting satellites, audio input, and power adapter.
Instructions for plugging in power, turning on the system, and adjusting volume and bass levels.
Resolve no sound by checking power supply connection and adapter.
Address low volume, unmute operation, and source device volume settings.
