What to do if Jensen VM9512 cannot insert disc?
If you cannot insert a disc into your Jensen Car Receiver, it is possible that there is already a disc inside the unit. Eject the current disc and then insert the new one.
Why Jensen VM9512 unit will not power on?
Your Jensen Car Receiver might not power on due to a blown radio fuse. In this case, install a new fuse with the correct rating. Alternatively, the car battery fuse could be blown, requiring a replacement with a correctly rated fuse. If neither of these is the issue, the unit might be in illegal operation mode; press the RESET button located in the bottom right corner of the front panel.
What to do if there is no/low audio output from Jensen VM9512 Car Receiver?
If you're experiencing no or low audio output from your Jensen Car Receiver, the cause might be an improper audio output connection, so check the wiring and correct it. Also, the volume may be set too low, so increase the volume level. Review the wiring diagram and check the “MUTE” connection in case of improper connection. Damaged speakers can also cause this issue, so consider replacing them. Heavily biased volume balance may be another cause; adjust the channel balance to the center position. Finally, ensure that the speaker wiring is not in contact with any metal part of the car, and insulate all speaker wiring connections if necessary.
What to do if Jensen Car Receiver remote control does not function?
If your Jensen Car Receiver's remote control isn't working, the battery might be depleted, so replace it with a new one. Another potential cause is that the battery is installed incorrectly; remove the battery and install it correctly.
Why Jensen VM9512 Car Receiver has poor sound quality or distortion?
Poor sound quality or distortion in your Jensen Car Receiver could be due to several reasons. You might be using a pirated disc, in which case you should use an original copy. The speaker power rating might not be compatible with the unit, so connect proper speakers. Lastly, the speaker could be shorted, so check the speaker contact.
What to do if Jensen VM9512 Car Receiver disc does not play back?
If your Jensen Car Receiver disc does not play back, the disc might be warped or scratched, so use a disc in good condition. The disc may be dirty or wet; clean the disc with a soft cloth. The laser pickup might be dirty; clean the laser pickup with a cleaning disc. An incompatible disc might be used; use a compatible disc. The disc rating might exceed the Parental Lock rating limit; change Parental Lock settings to a lower restriction. The disc region code might not be compatible with the unit; use a disc with the proper region code. Finally, the disc may be inserted upside down; insert the disc with the label side up.
Why Jensen VM9512 Car Receiver interruption occurred during playback?
If an interruption occurred during playback on your Jensen Car Receiver, the disc might be dirty or scratched; clean the disc or replace it. Alternatively, the file may be damaged or a bad recording; recreate the disc with good files.
What is Tel-Mute malfunction in Jensen Car Receiver?
A Tel-Mute malfunction in your Jensen Car Receiver could be caused by the “MUTE” wire being grounded. Check that the “MUTE” connection is not grounded and that it’s properly insulated.
What to do if Jensen Car Receiver prolonged image or improper height/width ratio display?
If you are experiencing a prolonged image or an improper height/width ratio display on your Jensen Car Receiver, it's likely due to an improper aspect ratio setup. Use the correct aspect ratio setting.
What to do if Jensen VM9512 Car Receiver has no image?
If there is no image on your Jensen Car Receiver, it could be due to an incorrect connection to the parking brake wire; check the wiring and correct it. Another cause might be that the PRK SW is activated and the parking brake is not engaged; stop the vehicle in a safe place and apply the parking brake.
General| Display Size | 6.2 inches |
|---|---|
| Resolution | 800 x 480 pixels |
| Touchscreen | Yes |
| Bluetooth | Yes |
| USB Port/Input | Yes |
| Built-in Navigation | No |
| DVD Player | Yes |
| Radio | AM/FM |
| AUX Input | Yes |
| Rear View Camera Input | Yes |
| SD Card Slot | Yes |
| SiriusXM Ready | Yes |
| Audio Formats Supported | MP3, WMA |
| Video Formats Supported | MP4, AVI, MPEG |
| Preamp Outputs | 3 (Front, Rear, Subwoofer) |
| Peak Power Output | 50W x 4 |
| Power Output | 50 Watts x 4 |
Steps to take before physically installing the unit.
Specific steps for installing the unit in an ISO-DIN dashboard.
Explains the function of the buttons on the main unit panel.
How to open and close the motorized display panel.
Procedures for turning the multimedia receiver on and off.
How to control the audio volume level using the unit or remote.
How to switch between different audio/video sources.
Adjusting equalizer, fader, and balance settings for sound.
Settings for clock, language, and display options.
Basic playback controls for audio discs like CDs.
Navigating and controlling the iPod via the unit's interface.
How to accept or reject incoming phone calls via Bluetooth.
To Next Page
