How to fix a Jensen Car Receiver that will not power on?
If your Jensen Car Receiver won't power on, the radio fuse or car battery fuse may be blown. Install a new fuse with the correct rating. Alternatively, an illegal operation may have occurred. In that case, press the RESET button located in the bottom right corner of the front panel.
How to improve weak station searching on Jensen VM9226BT Car Receiver?
Weak station searching on your Jensen Car Receiver can occur if the auto antenna is not fully extended or properly connected; connect the auto antenna control cable properly. Another reason may be that the LOCAL function is activated; turn the LOCAL function off.
Why does my Jensen VM9226BT reset when the engine is off?
If your Jensen Car Receiver resets itself when the engine is off, it might be due to an incorrect connection between the ACC and positive battery wire; check the wiring and correct it.
What to do if there is no audio output from my Jensen Car Receiver?
If you're experiencing no or low audio output on your Jensen Car Receiver, there are several potential causes. First, check your wiring to ensure a proper audio output connection. Next, verify that the volume isn't set too low and increase it as needed. Also, review the wiring diagram to check the “MUTE” connection. If the issue persists, your speakers may be damaged and need replacement. Heavily biased volume balance may also cause this problem, so adjust the channel balance to the center position. Finally, ensure that the speaker wiring is not in contact with any metal parts of the car; if it is, insulate all speaker wiring connections.
Why is the sound quality poor on my Jensen VM9226BT Car Receiver?
Poor sound quality or distortion in your Jensen Car Receiver can stem from a few sources. Using a pirated disc can cause this, so ensure you're using an original copy. Additionally, the speaker power rating might not be compatible with the unit; connect proper speakers. Finally, a shorted speaker can also lead to sound issues, so check the speaker contact.
What to do if my Jensen VM9226BT Car Receiver disc does not play back?
If your Jensen Car Receiver disc does not play back, there are several possible reasons. The disc might be warped or scratched, so use a disc in good condition. It could also be dirty or wet; clean it with a soft cloth. A dirty laser pickup can also cause this, so clean the laser pickup with a cleaning disc. Ensure you are using a compatible disc and that the disc region code is compatible with the unit. Also, check that the disc rating does not exceed the Parental Lock rating limit. Finally, make sure the disc is inserted with the label side up.
Why is there no image on my Jensen VM9226BT screen?
If there is no image on your Jensen Car Receiver, check the wiring to ensure correct connection to the parking brake wire. Also, make sure the parking brake is engaged by stopping the vehicle in a safe place and applying the parking brake.
Why is the image flashing on my Jensen Car Receiver?
If a flashing image or interference appears on the screen of your Jensen Car Receiver, the DVD may not be compatible with the current TV system settings; change the setup to accommodate the disc. It could also be due to improper video signal connections; check the wiring and correct it.
How to fix prolonged image on Jensen VM9226BT Car Receiver?
If your Jensen Car Receiver displays a prolonged image or an improper height/width ratio, it's likely due to an improper aspect ratio setup. To fix this, use the correct aspect ratio setting.
Why is the image on my Jensen VM9226BT Car Receiver blurred?
If the image on your Jensen Car Receiver is blurred, distorted, or dark, the disc may be illegally copied. Use an original disc to resolve this issue.
General| Brand | Jensen |
|---|---|
| Model | VM9226BT |
| Category | Car Receiver |
| Language | English |
Details on fast forward/reverse, slow motion, and playback controls for DVD discs.
Information on CD-Text, ID3 tag support, directory search, and burning files.
Details on connecting and controlling iPod/iPhone via USB for music and video.
How to turn the unit on/off and manage audible beep feedback.
How to navigate and select different audio/video sources.
Detailed guide on adjusting Bass, Mid, Treble, and EQ presets.
How to reset the unit to factory default settings.
How to enter a radio station frequency directly.
Storing and recalling radio stations using preset buttons.
How to access and use on-screen controls for DVD/VCD playback.
Procedure for inserting discs and accessing DVD mode.
Defines a specific area of a disc for continuous repeating.
Specifies compatible media formats for audio playback.
How to stop and pause playback of discs.
Compatibility for MP3/WMA files on various disc types.
Guidelines for file naming and compression for MP3 discs.
Information on playing files from MP3/WMA discs.
Steps to connect and access iPod/iPhone features.
Using the unit for hands-free mobile phone communication.
To Next Page
