Why does my Jensen VM9213 keep resetting itself?
If your Jensen Car Receiver unit resets itself when the engine is off, it's likely due to an incorrect connection between the ACC and the positive battery wire. Check the wiring and correct it to resolve this issue.
How to fix a Jensen Car Receiver that will not power on?
If your Jensen Car Receiver unit isn't powering on, there might be a blown fuse. Check both the radio fuse and the car battery fuse, and replace any blown fuses with new ones of the correct rating. If the issue persists, try pressing the RESET button located in the bottom right corner of the front panel.
What to do if there is no audio output from Jensen VM9213?
If you are experiencing no or low audio output from your Jensen Car Receiver, there are several potential causes. First, check the wiring and correct any improper audio output connections. Next, ensure that the volume isn't set too low and that the “MUTE” connection is properly wired according to the wiring diagram. Also, adjust the channel balance to the center position in case of a heavily biased volume balance. Finally, make sure that the speaker wiring is not in contact with any metal parts of the car, and insulate the connections if necessary. If the issue persists, the speakers may be damaged and need replacement.
Why is the Jensen Car Receiver remote control not working?
If the remote control for your Jensen Car Receiver isn't working, the first thing to check is the battery. If the battery is depleted, replace it with a new one. Also, ensure that the battery is installed correctly by removing it and reinstalling it properly.
How to improve sound quality on Jensen Car Receiver?
If you're experiencing poor sound quality or distortion with your Jensen Car Receiver, make sure you're using an original disc and not a pirated copy. Also, check that the speaker power rating is compatible with the unit, and ensure that the speaker is not shorted by checking the speaker contact. If the issue continues, connect proper speakers.
What causes flashing image on Jensen VM9213 and how to fix it?
If the image on your Jensen Car Receiver screen is flashing or showing interference, it could be due to the DVD not being compatible with the current TV system settings. Try changing the setup to accommodate the disc. Additionally, check the video signal connections and correct any improper wiring.
What causes Tel-Mute malfunction in Jensen VM9213 Car Receiver?
If your Jensen Car Receiver is experiencing Tel-Mute malfunction, it could be that the “MUTE” wire is grounded. Check that the “MUTE” connection is not grounded and that it’s properly insulated.
How to fix Jensen Car Receiver monitor that won't open automatically?
If the monitor on your Jensen Car Receiver does not open automatically, it could be because the TFT Auto Open feature is turned off. Turn TFT Auto Open on to enable automatic opening.
What to do if there is no image on Jensen VM9213 Car Receiver?
If there is no image on your Jensen Car Receiver screen, it may be due to an incorrect connection to the parking brake wire. Check the wiring and correct it. Also, if the PRK SW is activated, ensure that the parking brake is engaged by stopping the vehicle in a safe place and applying the parking brake.
Why is Jensen VM9213 Car Receiver having weak station searching?
If you are experiencing weak station searching on your Jensen Car Receiver, it could be due to several reasons. First, check if the auto antenna is fully extended and properly connected by ensuring the auto antenna control cable is correctly connected. Also, make sure the LOCAL function is turned off.
Details on optional modules like navigation and Bluetooth, and rear cameras.
Explains the functions of various buttons on the unit's front panel.
Details about the disc slot and the USB interface connector for media playback.
Lists and explains the functions of buttons on the remote control for different modes.
Covers screen adjustments, aspect ratio, parking brake inhibit, and monitor movement.
Explains powering on/off, mute, source selection, and volume adjustment.
Instructions on how to reset the unit to factory default settings.
Guides on accessing and modifying setup options like clock, tuner, language, and audio.
Details on Bluetooth pairing, rating, camera input, and TFT auto-open settings.
Explains the tuner display, band selection, seek tuning, and manual tuning.
Details on storing, recalling, and auto-storing radio stations.
Covers playback controls like play, pause, stop, fast forward, rewind, and repeat functions.
Explains menu access, chapter navigation, direct entry, angle selection, and multi-language options.
Outlines media compatibility, file naming, and basic playback controls for MP3/WMA files.
Details random playback, intro scan, direct track entry, and photo viewing.
Guides on pairing a phone, managing incoming/outgoing calls, and call transfer.
Covers managing incoming/outgoing calls, and call transfer.
Details accessing phone book, missed/dialed/received calls.
Explains A2DP audio streaming and switching between phone and music interfaces.
Addresses power, remote, audio, sound quality, and TFT monitor problems.
Covers problems with disc playback and interpreting error messages.
Details warranty terms, exclusions, and limitations on liability.
Lists the included accessories and components with the VM9213 unit.
Lists the necessary tools and supplies for installing the VM9213.
Outlines steps before installation, including disconnecting the battery and preparing the mounting sleeve.
Illustrates wiring connections and advises on fuse replacement.
General| Touchscreen | Yes |
|---|---|
| Bluetooth | Yes |
| USB Port | Yes |
| Radio Tuner | AM/FM |
| Rear Camera Input | Yes |
| DVD Player | Yes |
| SD Card Slot | Yes |
| Navigation | No |
| AUX Input | Yes |
| Backup Camera Input | Yes |
| Remote Control | Yes |
| Display Size | 6.2 inches |
| Audio Formats Supported | MP3/WMA |
| Display Resolution | 800 x 480 |
To Next Page
