EasyManua.ls Logo

Jetwave Scorpion G2 - User Manual

Jetwave Scorpion G2
20 pages
Save Page as PDF
Print Icon
To Next Page IconTo Next Page
To Next Page IconTo Next Page
Loading...
WATER JETTING/DRAIN CLEANING MACHINE
V1.0 - 2020
SCORPION G2 MANUAL - WATER JETTER/DRAIN CLEANER
®
Record Serial Number below and retain product serial number which is
located on nameplate.
UNIT SERIAL NO.
ENGINE SERIAL NO.
PURCHASE DATE
Cold Water Petrol Driven
WARNING!
Read this Operator’s Manual
carefully before using
this machine. Failure to
understand and follow the
contents of this manual may
result in electrical shock,
re and/or serious personal
injury.
READ CAREFULLY

Table of Contents

Questions and Answers

  • M
    Michelle AndersonAug 9, 2025
    Why is the pressure low on my Jetwave Ultrasonic Jewelry Cleaner?
    • S
      Susan MackAug 9, 2025
      Low pressure in your Jetwave Ultrasonic Jewelry Cleaner can be caused by several factors. First, the nozzle might be worn and needs replacement with one properly rated for the jetter. Check that all hose connections are tight to prevent air leaks in the inlet plumbing. The pump valves might be stuck, worn, or dirty, requiring professional servicing. The unloader valve may need adjustment, or the filter could be clogged and needs cleaning. Other potential causes include worn pump packing, abrasives in the pumped fluid, severe cavitation, or an inadequate water supply. To address these, clean the filter, confirm there are no water supply restrictions, and if issues persist, take the jetter for pump service.
  • L
    lindseykhanAug 14, 2025
    What to do if Jetwave Ultrasonic Jewelry Cleaner shuts off in use?
    • N
      nicholas48Aug 14, 2025
      If your Jetwave Ultrasonic Jewelry Cleaner shuts off during use, the most likely cause is insufficient water in the tank, which activates the low water float switch. To resolve this, ensure the water supply is turned ON and that the water supply hose is not kinked or collapsed, obstructing water flow. Also, verify the water level in the tank.
  • J
    Jodi LewisAug 25, 2025
    How to fix Jetwave Ultrasonic Jewelry Cleaner that won't adjust to full pressure?
    • F
      farmerkristenAug 25, 2025
      If your Jetwave Ultrasonic Jewelry Cleaner doesn't reach full operating pressure at start-up, it could be due to air trapped in the system or blocked jetter nozzle orifices. Try removing the nozzle and inserting the jet hose into the drain line to flush out trapped air or debris. Also, remove the nozzle and use a nozzle cleaning tool to clear any blockages from the nozzle orifices by pushing the tool completely through each orifice.
  • J
    John WatsonAug 29, 2025
    What to do if my Jetwave Ultrasonic Jewelry Cleaner won’t start?
    • L
      lmurrayAug 29, 2025
      If your Jetwave Ultrasonic Jewelry Cleaner won’t start, it could be due to not enough water in the tank or a clogged filter. Please refer to the troubleshooting steps for when the 'Jetter shuts off in use'. Additionally, clean the inlet filter.
  • J
    Jon FieldsSep 3, 2025
    Why is the pump running rough with low pressure on my Jetwave Ultrasonic Jewelry Cleaner?
    • W
      William BellSep 3, 2025
      If the pump in your Jetwave Ultrasonic Jewelry Cleaner runs roughly and the pressure is very low, this may be caused by inlet restrictions, air leaks on the inlet side of the pump, or a stuck inlet or discharge valve. To address this, check the hose from the tank to the pump for kinks and ensure all hose connections are tight. If the issue persists, it may be due to worn pump cups or valves, requiring professional pump service.
  • D
    Daniel LawsonSep 10, 2025
    Why does the pressure gauge oscillate on my Jetwave Ultrasonic Jewelry Cleaner?
    • N
      Nathan MorganSep 12, 2025
      If the pressure gauge on your Jetwave Ultrasonic Jewelry Cleaner oscillates from 500 to full operating pressure, it's likely due to blocked jetter nozzle orifices or trapped debris/air in the system. To fix this, remove the nozzle and use a nozzle cleaning tool to clear each orifice of debris. Additionally, remove the nozzle and insert the jet hose into the drain line, then run the jetter to flush out any trapped air or debris.

Jetwave Scorpion G2 Specifications

General IconGeneral
BrandJetwave
ModelScorpion G2
TypeUltrasonic Jewelry Cleaner
Ultrasonic Frequency42 kHz
Timer Settings180 seconds
Power SupplyAC 110-120V, 60Hz
MaterialStainless Steel